similar to: zaphfc error

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi, I have following problems compiling bristuff-0.2.0RC8m. Has anybody seen them before and can point me in the right direction? zaphfc/make all: ---------------------- /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c: In function 'hfc_findCards': /usr/src/asterisk/bristuff-0.2.0-RC8m/zaphfc/zaphfc.c:1000: error: invalid lvalue in assignment make[2]: *** [

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Hi Guys I have been running a test server for a few days now with * 1.0.9 bristuff RC8n. I had a power failure and the test machine was not on the ups. When power was restored I found the following error: FATAL: Error inserting zaphfc (/lib/modules/2.6.11.4-20a-default/misc/zaphfc.ko): Unknown symbol in module, or unknown parameter (see dmesg) My dmesg output: zaphfc: unsupported

I've got Zaphfc working running Asterisk v. 0.7.2 Then I have tried with Asterisk V. 1.0 and the latest from CVS - with no succes. Has anybody got zaphfc working with newer version than 0.7.2 ? NR -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040616/32481fca/attachment.htm

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hello all, I've a little clue with zaphfc used to connect to a BRI linethat probably can be a configuration issue.... (really I hope so) Here, telcos (expecially mobile operators) use to substitute the dialtone with some vocal indication without answer the line. (Indications like "The customer is not reachable" or "wait because the customer is on the phone" ecc..) For

Caller id is not in the configs that are supplied with zaphfc from bristuff, and it's not mentioned in the wiki. Is it possible to use callerid with zaphfc/bristuff? Thanks!!

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

After upgrading a CentOS 3.x box to CentOS 4.1 (both x86_64 with an Athlon64) I also wanted to get the latest bristuff. Unfortunately bristuff without florz causes the box to kernel panic within hours (console will complain about bad frame received something). It seems however that the florz patch will not work for x86_64 arch. Bristuff -0.2.0-RC8j compiles fine without the florz patch, but