similar to: Asterisk & Fritz & Capi & isdn PBX integration : Can I dial out on any MSN I declare ?

Hello, i wonder why i didn't find a solution for this problem yet, because it seems very common: I have an asterisk server with an AVM (Fritz) ISDN-Card (BRI), and some SIP-Softphones which i can call from outside by calling the phonenumber of the Asterisk-Server and then dialing the number of the SIP-Phone. If I make a call from a SIP-Phone into PSTN, only the MSN of the asterisk-server is

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hi, First, here is my config: Kernel version 2.4.25 on a Fedora distro, Asterisk and a Fritz! Isdn PCI Card (v2). I try to make the CAPI drivers deal with Asterisk but I can't try to figure out to get of this issue. As I see, Fritz modules are integrated with the kernel, so I directly loaded the 'hisax_fcpcipnp' module from it. I install also Capi modules by downloading archives of the

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

If I do that, the modprobe doesn't find any module called fcpci and is looking for any module called hisax_fcpcipnp as it's the one install for the isdn fritz card. # capiinit modprobe: Can't locate module fcpci ERROR: failed to load driver fcpci Maybe, I should reinstall the fritz card drivers itselves? (however, I don't think so...)

Hello! How can one select outgoing MSN when dialing out from ttyI-interfaces? I have successfully done this with CAPI e.g... exten => _XXXXX.,2,Dial,CAPI/60:bBYEXTENSION ...in extensions.conf. Currently correponding for my ISDN modem interface is... exten => _XXXXX.,2,Dial(Modem/g1:${EXTEN}) ...but this selects only MSN of outgoing group g1 for dialout MSN number. I also tried to

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Hi, I was trolling through the archive to see if it was possible for asterisk to ignore certain MSNs. I have a AVM Fritz/BRI with two MSNs: 7770001 and 7770002. I would like asterisk (with chan_capi) to ignore 7770001 such that a regular phone on the bus will ring; calls for 7770002 should be picked up by asterisk. I configured msn=7770002 incomingmsn=* within capi.conf and figured this would

Hi, how can I set up multiple ISDN controllers with chan_capi, so that every controller has its own configuration (MSNs to listen etc...) ? I know I can configure "controllers=1,2" in chan_capi's capi.conf but then the controllers have the identical configuration and context within asterisk. My setup: I have 2 BRI-controllers (in one AVM C2). 1. BRI: point-to-point, Number:

I tried that but it still doesn't work... I think I don't have the correct approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing with CAPI ? If yes, why shouldn't I use the hisax drivers (which are kernel ones) instead of fcpci drivers (which doesn't seems to work, by the way...) And finally, how is it possible to link the two modules together? As you can see,

I've put my fire proof suit on ready to ask a question ;o) Redhat 9 Kernel 2.4.20-8 AVM Fritz PCI Problem 1... i have followed instructions from:- http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI (Plus many many other sites found via google over the last 16 hours) after modifying the makefile & defs.h,

> > That is possible, how could I check that? > > I can see that IRQ 17 is shared between eth0 and my fritz!card > but I > > don't know if it changes anything: > > Can you try it (or eth0) in a different slot (or change IRQ's in the > BIOS if possible) to see if it makes any difference? That's the > only way > to know for sure, anything else is

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

<FONT face="Default Sans Serif, Verdana, Arial, Helvetica, sans-serif" size=2><div>Finally, i will get back to a RedHat 9 distrib as I see that it works with that distribution...</div></FONT>

Hi All, Many thanks to Marc who helped me with a previous Capi Dialout plan - however..... What I now would like to be able to do is: - We have 8 msn's 383590, 383591 383592 etc. What I would like to do is set up an If Then Else type statement along the following lines: - If extension 7957 Then Dialout on Capi msn 383590 ElseIf extension 7958 Then Dialout on Capi msn 383591 ElseIf

Hi All, Could somebody please help me to understand the following: - We have 8 msn's 383590, 383591 etc. What I would like to do is for the person at extension 1 dial out on 383 590, the person at extension 2 dial out on 383 591 etc. I have got myself so confused that I need major help!!! If you could give me a simplistic example, including which files I put the coding in (i.e.

HI all, Has anyone succesfully installed an AVM Fritz! card on Fedora 7 using the drivers at ATrpms recently? http://atrpms.net/dist/f7/fcpci/ I tried with a clean F7 build on my EPIA 5000 yesterday, after modifying /etc/capi.conf (removing the coment # in front of fcpci line) I received the following error when executing 'capiinit' - FATAL: Error inserting fcpci

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)

I really can't understand what is happening. I have the same set up in two locations:- 2 fritz cards in each with the patches and the same capi.conf except for the MSNs. One installation calls in on controller 1 and starts calls out on controller 2, i.e. perfect. The other calls come in on both controllers at the same time. I have checked the patches etc. Is this possibly a problem caused