similar to: PSTN tones with ISDN4Linux

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

Hi, i install the Asterisk PBX on a linux machine with i4l to connect to PSTN (EuroISDN). And i configure a very simple dial plan in extension.conf. After this, i connect with a SIP program to asterisk and would call my cellular phone, but got this error: -- Executing Ringing("SIP/ACzerniak-0904", "") in new stack -- Executing Dial("SIP/ACzerniak-0904",

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --

Hi all, I have this weird problem. I'm running asterisk 1.0.3 on Debian Sid (official debian package). We have 2 fritz ISDN cards. All is working great. Till I called the bank. It rings one time and then gives me the congestion tone. Here is what I see on the CLI (phone nr obfuscated for privacy reasons): -- Executing Dial("SCCP/michiel-00000004",

Hello, I would like to ask if anyone has solved the problem with Asterisk+ISDN4Linux cards, where there are no call progress tones or announcements from the PSTN when we dial ouot through the i4l card. For the moment, if we don't inject the r option in the Dial command, there is only silence during the call negotiation... Using Asterisk RC2 with Eicon passive PCI 2.01 card... Thanks for

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hi. I'm working with i4l with asterisk CVS-02/21/03-13:59:12, plus i4l (chan modem i4l *dsp patched* and kernel 2.4.19 patched to disable dtmf). All seems ok (apart some echo issues that seems gone with mec2 aggressive suppressor), but outgoing dtmf doesn't work . or at least I hear the very first part of the dtmf, but then it seems suppressed. here's my modem.conf [interfaces]

Hi everybody ! I've a Pentium IV with a USR ISDN PCI Card W699. Card I've installed asterisk 1.0.0 and it's working fine with outgoing call to POTS But it never answers to my incoming call from POTS and I don't understand why. I tested the modem also with the minicom utility and I never saw the "RING" status It seems that the modem didn't know somebody is

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

Hi, try to setup asterisk as an ISDN2H323-Gateway. The only problem i have after establishing a call is, that Audio works only from IP to ISDN-Phone but not from ISDN to IP-Phone. A known problem ??? Thanks in advance Michael i am using asterisk-cvs, pwlib V1.6.6 (janus), openh323 V1.13.5 (janus) and oh323-0.6.0 Here are my config's ############## # modem.conf # ##############

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

hi I have a passive isdn port configured in modem.conf in extention.conf i use this two channel (ttyI0 and ttyI1) with the string: exten => _NXXXXXXXXX,1,Dial,Modem/g1:${EXTEN}|60|r how can i hide my msn? is it possible to activate the clir with the @ before the ${EXTEN}? thanks Cristian