similar to: HFC-S ISDN card on *@home

I'm still trying to install a HFC-s BRI card onto *@home .6 I'm new to this so I probably am overlooking the obvious. Can I just install BRIstuff onto a fresh *@home install? The BRIstuff installer downloads another * from Digium. Will this interfere with the @home install and must I comment out the Asterisk install in the BRIstuff install.sh file? Any pointers are much appreciated.

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

This is my first posting to the list. Thus hopefully the question has not been asked several times before... I'm trying to install asterisk on a PC using Debian Sarge but without any real success... Problem: I may get the Asterisk packet (Debian version) installed using 'apt-get install asterisk', but that does not include the bristuff from Junghanns

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi Alessio Yes, the problems you report do seem similar to the issues I had. I found on the Dells that the audio prompts were very choppy and played slower than normal. Occasionally there would be 'bursts' oav a second or so of 'good' audio. I also suspected IRQ issues but the Dell Mobos had no way of adjusting them. Best thing is to try and get the card on its own unshared

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hi Guys, I got 2 internal HFC-S[5] (not sure what character this is) internal modem cards yesterday, thought I would get different makes as the one was a named brand, the other not... but anyway... Its picked up by lscpi as a ... "Network Controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)" I'm using kernel 2.6.10, and I saw I must use CAPI. I

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the