similar to: quadbri and spandsp

hi does any body know which version combination of spandsp/tx_fax/rx_fax will work with * 1.2.24? i tried different combo. they're either seg fault during runtime or won't compile. very frustrated :/ p.s. i know. hylafax/iaxmodem is far more stable. but i have specific reasons to use rx_fax. -- Edwin Lam <edwin.lam at officegeneral.com> Systems Engineer, Office General, Inc.

Aloha, We are looking to roll a solution that will have the following network layout: ISDN-PRI <--> Asterisk <--> T.38 <--> ATA <--> Fax Does version 1.8 with the Digium fax driver have this capability? I like 1.8 because it is a long term support version. What ATA's are people using? Any working solutions would be great! Aloha, Matt

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

I''ve got a situation where a manifest fails when writing one particular key for a user. What I have is a manifest that looks like this: class my::accounts () { Ssh_authorized_key { ensure => present, type => ssh-dss, } Then, after making sure the user, group, and authorized_keys2 file exist: ssh_authorized_key { "key-name-1": key

Hello, We have a quadBRI in NT mode with bri_cpe_ptmp signalling and when connect a ISDN telephone to this nothings happen. What can I do? My config files are this: Zaptel.conf: loadzone=es defaultzone=es # qozap span definitions # most of the values should be bogus because we are not really zaptel span=1,1,3,ccs,ami span=2,1,3,ccs,ami span=3,1,3,ccs,ami span=4,1,3,ccs,ami bchan=1,2 dchan=3

Hi ! Does anyone managed to send multipage faxes (in single TIFF file) with app_txfax from spandsp package (i'm using 0.0.2pre18, libtiff 3.7.1)? If so, I'm interested in format of TIFF file that has been sent sent succesfully (tiffinfo <fax-filename>). I'm having problems with app_txfax, sending first page successfuly 99 % of the time, but never managed to send second or

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Who is selling the quadBRI cards, which is everybody talking about? And how much does is costs? I'm looked on the site of junghanns.net, but there is no selling information. A seller in germany is favored.

Hello everybody, I've got Asterisk 1.2.4 running with two Junghanns QuadBRI cards using the qozap driver from bristuff 0.3.0-PRE-1l. One of the cards is running in TE mode, the other one in NT mode. Whenever I call into an empty MeetMe conference room on one of the NT ports or via SIP and hang up the call during the "you are currently the only participant in this conference"

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hello all, After compiling successfully Asterisk and AMPortal, I cannot make the fax module work. Asterisk does not start (unless I remove the modules or mark them as Noload in modules.conf) with the following error: Jun 3 20:55:25 VERBOSE[3328]: [app_rxfax.so]Jun 3 20:55:25 WARNING[3328]: /usr/local/lib/libspandsp.so.0: undefined symbol: dds_modf Jun 3 20:55:25 WARNING[3328]: Loading

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.