similar to: Using zaphfc and wcte11xp at the same time problem

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Hi ""noobs"" and others(like me). I've been struggling for hours,days,days,days.... to get my Asterisk work with 2x HFC-S BRI cards. One card for use in NT-mode for connecting my ISDN DECT phone,and one card as gateway to PSTN. Now it'works,and I just want to share some of the experience with others. I'd guess there must be 'Somebody Out There' having

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

Hi there, I am using bri-stuff.0.1.0-RC2k and it seems that things didn't become better. I have got lots of dropouts on the IAX2 link (no matter if jitter buffers are enabled). Further the MP3Player application does not playback streams like http://somestreamserver/somestream. It stops saying: -- Executing MP3Player("SIP/27870-ba4f",

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

I am running Asterisk 1.0.9 and the latest bristuff in combination with a HFC isdn card, connected to a BRI interface. For some reason, I am not able to have it dial out (see below). It exits with DIALSTATUS=CHANUNAVAIL. One thing that may be misconfigured is that it says: Signalling Type: PRI Signalling. How do I change this? Or is this the correct value? I posted my configs below. ------

Hello, I have asterisk@home with zaphfc patch applied (http://dondisperato.blogspot.com/), but I can not make call to legacy PBX (Alcatel 4400). I can only accept incoming calls. I am dialing with this: exten => 202,1,Dial(Zap/g1/242) --- asterisk1*CLI> bri debug span 1 Enabled debugging on span 1 -- Executing Dial("SIP/201-4678", "Zap/g1/242") in new stack

Hi everybody, I had an ISDN card with winbond chipset and isdn4linux, but there was a lot of echo when call from SIP to ISDN, so I buy an HFC chipset card (Conceptronic c128i). I downloaded and compiled bristuff-0.2.0-RC5 and everything is going fine. The sound quality is excellent, there is no echo, but i have a strange problem. Sometimes calls made from SIP phones to ISDN just finished

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Try commenting out the line pritrustusercid = yes Or set it to 'no'. That worked for me. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jens Sent: Friday, January 21, 2005 7:18 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] zaphfc no callerid

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to