similar to: Teles PCI and chan_capi, possible ???

Hello, folks! This is my first post here. I installed Asterisk from scratch and after reading a lot of information on voip-info and this mailing list I was able to get started. I can make sip-to-sip calls (just on a basic extentions structure, let's say for beginners) but now I'm trying to make this system works with my Teles ISDN BRI PCI card. I can make and receive calls through X-Ten

I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1 Anyone was able to use this card with asterisk? I couldn't find much information about it. Any help?

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello! After LOTS of research on this list and internet in general I managed to get an old Teles PCI card working with Asterisk throught ISDN4Linux. No echos, no delays, simply perfect -- electronic poetry ! :) eheheheheh I just didn't get it to work with CAPI and "chan_capi" but, since isdn4linux is doing such a good job, I'll

Hi I'm using a Teles ISDN passive card configured in modem.conf. when i make call from my sip client (xtex x-pro) to the external world i have more than 1 second of delay and echo very. There is some tuning to do? The performance is better with an active ISDN card or CAPI compatible driver? thanks mark balester

hi PSTN <--> [Teles ISDN / Asterisk] <--> SIP client When call is made through ISDN, no matter if taken from PSTN or Asterisk side, person in PSTN side can hear perfectly but in Asterisk side I only hear a very scrambled or very low quality voice, words repeated several times. Same is with echo test (call taken from PSTN) Setup: * Teles 16.3 ISA ISDN card with hisax kernel module *

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hi I was using asterisk 1.0.7 until now. For my connection with the PSTN I used a good old isa hisax teles 16.3 isdn card. Now while compiling 1.2 I nothiced that i4l and chan_modem is no longer supported? Is there any way of getting my good old ISA card to work under 1.2? The docs keep saying use misdn, capi, etc from now on. But I don't think my card is CAPI capable arne --------------

Hi, i'm traying to compile asterisk on my pc, a laptop whit SUSE 9.1 and a desktop with SUSE 8.2, with a teles S0 16/3 PnP. With Kernel 2.4 (Desktop) Asterisk run but it's umpossible to compile the driver ISDN-utils for Teles. With kernel 2.6 I can't compile zaptel (not necessary with my laptop) and asterisk, in both cases I receve errors during make or make linux26 (I saw the notes

Hi all, I'm struggling some time now with this problem. Googling and searching on this topic did not deliver the answer yet, so my last hope is this list. Analogue to the things which are possible with modem.conf, where I can configure the MSN's to act on, I would like to have similar functionality. This is the idea: I have 1 ISDN line, it can be reached by 4 different MSN's. I have

Hi, i am testing stuff for a couple of days now with Asterisk CVS-v1-0-07 and everything worked fine sofar when suddenly the voicemail and musiconhold sound output stopped working. The voicemailmenu still works though. I can see the voiceprompts etc in the debug messages on the asterisk CLI but i cant hear anything. Everything else works fine though. I can call out fine etc. I did some network

Hi, after getting the chan_capi error messages sorted out, I have another question. Calling * via SIP produces very good sound. Calling * via the chan_capi produces horrible sound. However, if I dial 500 in the demo menu to connect to the IAX at digium the sound is good again. ie: ISDNCall->AVM-B1-Card->Asterisk = All prompts sound horrible SIP->Asterisk = Prompts are good

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

hi all, i have one (teles) pbx with a BRI telephone and an outgoing E1 port. The outgoing E1 is connected to an pri_net port from my *. The incoming call will dail out to a h323 soft phone like openphone or sjphone or just netmeeting. The call will be conneted, but i don't hear any sound, from no one of the both sides. Can somebody help me? Thanks, Thomas.

My system is: Redhat 9.0 + Asterisk + ISDN4Linux + Teles 16.3 ISA Passive card I haven't sound card. Comunication between two SIP Clients is OK Comunication between PSTN and SIP Client is OneWay (i cant recive dtmf and voice from pstn) is it needed sound card ?

Dear Sirs, I have been using the package staRt but it has disappeared from the latest R versions. I emailed the author but he never replied. Is it possible to let me know if that package has been removed or if it has been replaced by another or what happened? The latest version is 1.1.12. I would like to know if I can keep using it or not. If it has been permanently removed, I should look for

Hi all! After much struggling I got my *@home working fine AND making use of two AVMFritz!PCI cards. Really nice ! (kernel 2.4.2x) There's however a silly glitch that's getting on my nerves, and, kind of a newbie that I am to linux, it should be easy to get help : -- "capiinit start" MUST BE run before Asterisk. (any other way makes * not to start because chan_capi

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hello all I found a bug in the chan_capi driver (really a not implemented message handling and then a false error condition) and I guess I have wrote a patch to fix it (basically I searched the internet for other capi open source implementation an borrowed the code snippet) but I don't know where to send the report and bugfix. I also found some miss-behaviours that I would like to share

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an