similar to: Put call on hold

I'm looking to handle 3 PSTN lines with my Asterisk server. I have a Digium TDM22B and Sipura 3000. The Sipura works great, but the TDM22B seems to have terrible problems with my board---virtually all peripherals need to be disabled in BIOS, and then there is terrible noise, terrible silence and virtually no ability to use DTMF in IVRs. I really wish the TDM22B worked, because I much

I'm having problems with a TDM22B. The FXO modules work fine. Both FXS modules fail to initialized. The error messages I see when the module loads: Init Indirect Registers UNSUCCESSFULLY. Indirect Registers failed verification. I already RMA'ed a TDM22B because of this problem. Now that the replacement shows a similar issue, I want to see if anyone else can think of something to

I just got my TDM22B, but the package did not include anything else, like datasheet. 1. Where can I download it? 2. Which outlets are FXS/FXO ??? (depending on the green /red card positions) 3. Does it need the extra power?? bye Ronald

Hi, I am using asterisk 1.4 with Digium TDM22B card. My system is running well except CALLERID. I have tried all options for cidsignalling, cidstart but no luck. Btw, I am living in Malaysia. From google web site, I found some one having the same problem with new version of asterisk but not in old versions. I do not want to try the old versions of asterisk. I really appreciate if someone can

Im getting the following error when I try to start Asterisk WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open channel 1: No such device or address I'm using a TDM22B card. ============= # Zaptel Configuration File # loadzone=us defaultzone=us fxoks=1-2 fxsks=3-4 ==============

Is there a way to test if the motherboard is ready for a Digium card (PCI 2.2) ? I would like to know from a remote computer, where I have (root) access, if this computer is ready for a TDM22B. bye Ronald

Hi All; If one of my FXS port damaged at TDM22B because we connected the Telephone Line cable to the FXS port while it should be connected to the FXO port, then can I order S110M FXS Module and fix it instead of the damaged FXS? (This if we assume my problem that really the FXS port damaged). Rregards Bilal

Hello everyone. I'm new to Asterisk but got some basic functionality going last night and I'm just giddy to have my own PBX ;-) Sorry if these are silly questions: My Asterisk server has the TDM22B (2 FXO, 2 FXS) interface. I have a very basic PSTN line coming in from the phone company, I tried to get the most no-frills line possible (didn't pay for caller ID, voice mail, etc.). I

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

Hello. I have this problem. In my asterisk box, I was running debian woody with asterisk package from backports.org. Last friday I upgraded from debian to sarge and change from kernel 2.4.18-1-686 to kernel 2.6.8-1-686, rebuild zaptel kernel module and also upgrade to asterisk 1.0.2. But now asterisk won't start. Here is more info #asterisk -vvvvvvvv (last lines) [chan_zap.so] =>

Hi I'm sorry for the my trivial quest. I Have asterisk 1.4 with TDM 400 with FXO and FXS, and works fine from several months. Now I want to connect a device to TDMFXS that want a ring frequecy of 25 hz to activate: i am italian, and usually the ring freq is 20 hz. The other time (I have used that device several times with other asterisk installation) I have modified /etc//modprobe.conf and

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hello, I've got 2 analogue lines (from SBC) coming into a TDM22B. SBC have put rollover from the first to the second line. The rollover works fine when handsets are connected directly to the lines (ie when Asterisk is not involved), but when the lines are connected to Asterisk, the rollover fails: the caller just hears the line ringing, and the person on the first (busy) line hears call

I have a TDM22B (TDM400 PCI + 2xFXO + 2xFXS). One FXO is connected to the PSTN. When Asterisk places a call, it dials using DTMF. If I listen in on the line during the dialing, there is a roughly one second pause between the penultimate and the final digit -- proportionally much longer than the pause between the preceeding digits. This accounts for about 25% of the time taken to dial. Anyone

Two asterisk, one in a 2.4.x and another one in a 2.6.x are connection ok using IAX, before i upgraded one of them (the one with 2.6.x) Trunk was working ok. Since i upgraded the one that its now 2.6.x, i m getting this message: chan_iax2.c:5067 socket_read: meta trunk cmd 1 received, I only understand 0 (perhaps the remote side is sending trunk timestamps?) ..and no sound comming from the

Hi all, I have installed a TDM22B on an IBM xSeries 220 with FedoraCore 3 and setup asterisk cvs head to work properly. A few days ago, I tried to update the system kernel to 2.6.12 from 2.6.9 and also to change to asterisk stable 1.0.9. After compiling zaptel and asterisk, i loaded zaptel and tried to load the wctdm module but this failed with the following message: Notice: Configuration file

After deciding to move a semi working asterisk setup to another box, installing and recompiling asterisk, addons and zaptel, modprobe zaptel says, module not found. Following various tales of how to modify udev stuff, still get that error. lspci does show the board in the list. All the LED's on the back of the board are dark. I have a TDM400p (tdm22b). I did not actually install the

Hello, I'm having a problem in voicemail check attempts from SIP-based phones. I've searched a ton of docs but don't see anyone else having a similar issue. I have a TDM22B with two non-sip phones connected to it as well as several SIP phones including a GXP-2000 and some X-Lites. Users of the real phones in the same context can pick up and dial *8 to get to VoiceMailMain() just

I have Asterisk voice mail setup locally. It works great, I'm impressed! Some details about my system: I'm using a TDM22B card to interface with both the PSTN and a VOIP provider. I'm running 1.2-beta from CVS. I have a regular VTech phone plugged into one of the FXS ports. Asterisk is able to indicate when a local voicemail message is waiting via the LCD display of my analog phone.