similar to: Intermediary jitter buffering

I am having a problem with Polycom auto-answer. I have the auto-answer working between PhoneA and PhoneB, but when I try to use the intercom between more then one phone I start having problems. PhoneA dials *3 which calls PhoneB, PhoneC, and PhoneD. All the phones ring, but only one will pick up, the rest will hang up and I get this error on Asterisk: Got SIP response 500 "Internal Server

I have just started to play with callgroups and pickupgroups.. I updates my * from CVS this morning (about 15 mins ago).. I have placed callgroup=1 and pickupgroup=1 into each of my 3 phone configurations in sip.conf.. I place a call from phoneA to phoneB, then I go to phoneC and dial *8# , the call does not get picked up by phoneC and continues to ring on phoneB.. Have I not configured

Hello all, Not sure if this mail belongs to this users or dev list. Sorry about that. We have the following scenario: PhoneA OpenSER Asterisk PhoneB PhoneC | | | | | | | | | | | | | |

Hi, Below is my case. phoneA (PSTN) phoneB (SIP) phoneC (PSTN) phoneA --> asterisk --> phoneB phoneA (music on hold), phoneB --attended call transfer--> phoneC phoneA --connect-- phoneC after phone B hangup phoneA type some keys in keypad but phoneC always has wrong dtmf detection. In my case, I would like to know any factor that will cause the wrong dtmf detection.

Hello, I am building an asterisk PBX with some stuff to make a usable VOIP / PSTN Gateway. I use the following devices: SIP Phones from GrandStream for VOIP side OpenLine4 from voicetronix for PSTN Side I am building things step by step with some priorities. I have now a working system able to place and receive calls from/to pstn. Before attempting to bring other functions (like voice

Hi, I got a weird behaviour in asterisk (original found in 1.8 but it is still the same in 11.15.0). I have three phones communicating via OpenSIPs with asterisk. Phone A dials 100 and asterisk calls SIP/phone-b. Phone B accepts the call. The User on Phone B places the call on hold, dials 200 and, while hearing the dial tone of ringing Phone C, places the handset on hook. Phone B sends a REFER,

I can't seem to retrieve a parked call. Here is what I do: Call from phoneA to phoneB Answer phoneB Press Flash/Callwait on phoneB Press 700 to park the call A voice says that the call is parked at 701 When I try to dial 701, I don't get connected to the parked call Below is the asterisk output when I tried to park

This is a real 'newbie' type question, but I can't get my brain to work today. Is it possible to re-direct an incoming SIP call based on it's CLI? Ideally I would like to check incoming calls against a short whitelist (of say 20 numbers) and redirect to a different extension if there is a match. I would also like to redirect calls that fail to present any CLI (aka

I have an ISDN line with 10 numbers. The line is then connected to * with one HFC-based card. The format of the numbers is like below: 123456-0 123456-1 ... 123456-9 Now I would like to connect those numbers to different telephones, i.e. when someone dials 123456-0, he/she is connected to the digital receptionist. If someone dials 123456-2, the connection goes to SIP/202 If someone dials

Hi, I'm looking for a way to reject a call remotely using the Asterisk dialplan. For example, phone A is ringing - I'm at the other end of the room next to phone B, and I want to reject the call to Phone A by dialing an extension. I'm basically trying to reproduce the Polycom "reject" action but through the Asterisk dialplan. Reasons: 1. It would allow me to

Hi All, I'm having a really weird can reinvite issue. I've been banging my head around on this for days now.. I have two asterisk servers. One at 172.20.0.11 One at 172.20.2.5 172.20.0.11 is a hosted box and serves multiple offices 172.20.2.5 is a box on site at a customer's office. A phone at 172.20.128.10 makes a call using server 172.20.0.11 to a phone at 172.20.2.80 via server

Hi there, I had a problem, basically, I have 4 different types of end users (gsm, ilbc, g729, ulaw). However, I only have one user with my DID provider. My provider supports all 4 codecs. The issue is then: When an incoming call comes in, a codec is negotiated (usually ULAW), later on, when the extension is dialed, we'll see we're doing GSM, and thus transcode. Here's an example

Hi all, I have a problem with using remote MySQL database server with two Asterisk (1.4.17) servers. PhoneA registers with Asterisk#1 using realtime into MySQL on remote server and everything is working fine and when I call Phone A from Phone B (also registered with Asterisk#1) call is established. Problem is when I call PhoneA (which is registered with Asterisk#1) from PhoneC (which is

I'm using rsync, ssh, and cron glued together with Python as a push-based synchronization system. From a single location, I push content out to various offices. I log stdout/stderr on the master server to make sure everything is running smoothly. I would now like for some of our "regional hubs" to take on some of the load (bandwidth-wise), while still retaining my centralized

Is it possible to a configure a tinc (1.0.35) node to only send outbound through specific nodes, rather than trying to establish direct connections? I have a node which can connect to all the others directly, but some routes have terrible packet loss, so I'd like to configure it not to try. thansk Hamish

On 22/9/20 4:44 pm, Hamish Moffatt wrote: > Is it possible to a configure a tinc (1.0.35) node to only send > outbound through specific nodes, rather than trying to establish > direct connections? > > I have a node which can connect to all the others directly, but some > routes have terrible packet loss, so I'd like to configure it not to try. Anyone? Should I just

On 7/10/20 2:45 pm, Erich Eckner wrote: > Hi, > > On Wed, 7 Oct 2020, Hamish Moffatt wrote: > > > On 22/9/20 4:44 pm, Hamish Moffatt wrote: > >> Is it possible to a configure a tinc (1.0.35) node to only send > outbound through specific nodes, rather than trying to establish > direct connections? > >> > >> I have a node which can connect to all

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA256 Hi, On Wed, 7 Oct 2020, Hamish Moffatt wrote: > On 22/9/20 4:44 pm, Hamish Moffatt wrote: >> Is it possible to a configure a tinc (1.0.35) node to only send outbound >> through specific nodes, rather than trying to establish direct connections? >> >> I have a node which can connect to all the others directly, but some

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm doing some basic operations on large sparse matrices, for example getting a row. it takes close to 30 seconds on a 3Ghz machine, and shots the memory usage up to the sky. I suspect there are dense intermediary steps (which, if true would defeat the purpose of trying to use sparse representaitons). As much as I try understanding the

[sorry for the loss of proper attributions, this is from two messages]: [Me] >This is something I've encountered in trying to make a particular > asterisk application handle properly IAX2 frames which contain either > 20ms of 40ms of speex data. For a CBR case, where the bitrate is > known, this is fairly easy to do, especially if the frames _do_ always > end on byte