similar to: chan_capi and asterisk

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Your Zap conf files would be helpful. Zttest results? Cat /proc/interrupts. Sharing interrupts? Any funky error in the logs? Thanks, Steve Totaro http://www.asteriskhelpdesk.com > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Administrator TOOTAI > Sent: Thursday, May 10, 2007 6:24 AM

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

hello, i have a problem on started asterisk, when try to start asterisk a get the fowlling error: chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) Feb 17 11:34:01 WARNING[3104]: config_old.c:27 ast_load: ast_load is deprecated, use ast_config_load instead! == Parsing '/etc/asterisk/misdn.conf': Found Feb 17 11:34:01 WARNING[3104]: config_old.c:39 ast_destroy: ast_destroy

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser

HI: Is there any way to raise up sound volume on fxo on TDM04B without changing tx-gain and rx-gain ? __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Hello, I have problem with capi, I can't install it. I have putted all info what I did and what I get :). I think you can suggest me how to solve this problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI v2.1and I want to install it to my ubuntu box (kernel: 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds this card: *02:0d.0 Network

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hi, My asterisk server was working with a 4-FXO analog card (TDM400P). I recently added two digital cards: a TE120P (1 PRI) and a B410P (4 BRI). The B410P is still unconfigured but inserted in a PCI slot. The TE120P's jumper is set to E1 as it will connect to a commercial PBX's PRI card also configured as E1. My analog channels used to be 1-4 but since I added the new cards I changed

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

Hi Jon, perfect instructions, thank you very much. I used them and after some tests they worked. Here is what I did. Maybe someone could use it completely: ------------------------------------------------------------ Install helpers: apt-get install kernel-package ncurses-dev fakeroot wget bzip2 Go to usr directory: cd /usr/src wget

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hi, I've been having problems getting Asterisk to work with a fritz card (in ptp mode). We've managed to get everything configured, however, as soon as the call is connected we get "Unhandled message: prim 281 len -22 from addr 1000000, dinfo 0 on this port" I checked, and mISDN_dsp is loaded. Any help would be much appreciated! Regards, Chris Jones // Network Administrator

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?