similar to: Need help with a Cisco 7960

Hi all, i have a problem with some cisco 7960. Yesterday i did a firmware-upgrade from 3.1 (1.2) with P0S30203.bin as described in the most documents. Now i get the message Phone unprovisioned and in TFTP-Log i find the following line: 07.03.2005 19:58 :Timeout error sending P0S3-07-3-00.bin to 192.168.0.83, 0 bytes So i think it now wants to load the file P0S3-07-3-00.bin. But i have not

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -

Hi! I did manage to load phone with SIP image : SIP70.8-0-3S, made SEP-MAC.cnf.xml, but phone never read the configuration from it. On the screen it's written "Unprovisioned", and phone is not trying to register with asterisk. Please help!! MihaelaMJ -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a stupid question. How do you remove line presentations on a cisco 7960 ? I have 3 line presentations I don't use anymore and I can't figure out how to remove them.

Running those versions of code, my 7960 will not register with Asterisk. The same 7960 is authenticating against another * server on line 2 just fine though - with the same settings in sip.conf. On the failing * server I am just getting 401 unauthorized errors on the console. From the phone's shell I get that t is registering, but not authenticated .1. from show reg. Any ideas would be

I have three questions about my 7960 phone that I can't discern from the docs/wiki. 1st - If I change the SIPxxxxxx.cnf file to change registrations it sets up new lines as expected. If I delete a line it doesn't get removed when I reboot the phone. I have to go to the phone, unlock it, and reset the SIP parameters. How do I make it "forget" what it has programmed and

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031207/e5e9b8eb/attachment.htm -------------- next part -------------- Hello all, I am newbie to Telephony world (IP and PSTN). Please excuse me if you find my questions very dumb. I am trying to configure my IP 7940 with the Asterisk, when phone boots up it only shows the message "Phone

Folks, I have CISCO 7940g phone. I have in the past configured the phone with two lines. Having found the 2nd line wasn't much use, I want to remove it from the config. I have taken it out of the SIP config file that is TFTPd to the phone but it is still showing on the phone and it is still trying to log into Asterisk with that account. I have tried removing the config line and blanking

I'm trying to connect a Cisco 7942 to my Asterisk box. I have a 7960 and 7912 currently connected and functioning. I'm trying to use the recommendations from here: http://www.voip-info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP I have created a "XMLDefault.cnf.xml" and it took the latest image but the phone states it's unprovisioned? Any

Hi Everyone, I am having some issues getting my 7961 working with Trixbox. I have loaded the SIP code (8-3-3SR2) fine but when the phone boots up it goes into an unprovisioned state. A status message shows up and says ?Error Verifying Config Info?. I have read quite a bit on this topic (getting 7961?s to work with Asterisk and TB) and only came across a few postings where other people

I have Asterisk version 1.0-RC1 running on Debian Woody. I have 1 analog phone working, 2 inbound lines working, X-Lite is working. The problem that I am having is with Cisco 7960 with SIP version 7.2 software. I can make outbound calls and they work fine, I even get a notice that I have voice mail on the phone and it seems to register properly but I can seem to dial to the phone.

Anyone have experience with the 3-08-2 release of Cisco's SIP firmware? Are there any new features in the SIPDefault.cnf? Thanks, Ron

I know this isn't a specifically asterisk question, but does anyone know how to make the phone NOT use it's old config? I'm trying to get rid of the second line registration crap and it's not working. Aaron

I'm starting out w/ a Cisco 7940, running the Sip image version 6.3. I've downloaded/installed asterisk via cvs. I've set the phone up to get its info via dhcp - the dhcp, tftp, astericks box & phone are on the same network. I've gone through and setup a test account per the instructions @ http://voip-info.org/wiki-Asterisk+phone+cisco+79xx but time I do a sip show

I have read the wiki and several other internet documents. Can anyone make a comment as to what kind of functionality will you loose if you use Cisco 7940 phones with asterisk 1.4 things like: MWI, call transfer, conference,etc,etc. I have a customer with 6 of those phones that he like to use with the asteirsk PBX. thanks, -- ------------------------------------------------------------ Erick

I've just recieved a copy of the new SIP firmware for the Cisco 7970, those of you with Cisco accounts may wish to try it (shock horror I'm sticking with SCCP). This coincides with the release of v8 firmware for all Cisco phones (and for those of you running Sergio's chan_sccp v8 works fine) The firmware is now also (and for the 7970 SIP, only) distributed in ".cop" files,

Hi all, Is it possible to have the Cisco 7960 dialing a SIP address to a service that you are not registered with, for example: sip:xxxxxx at xxxxx.org and asign that to some spee dial button? I have heared that it should be possible to define in the dialplan.xml file, but not sure. Any info is really apreciated, many thanks! Christian

Hi all, This might be a little off topic, but I need some help with this phone and hopefully someone on this list is able to assist me. When establishing a conference call I am not able to hang up the call I connected to my original call. I have tried pressin ghte conference button, but nothing happens. Any help would be apreciated, many thanks! Christian

Hello specialists In setting up a diskless X-Terminal I got stuck with the transfer of the ramdisk from the server to the target. With a ramdisk image size of about 60 Mb things go well, the file gets transfered completely and Linux boots perfectly. With a ramdisk image size of about 104 Mb the tftp transfer of the kernel succeds but the transfer of the ramdisk image fails. As tftp daemon I

Anybody know the proceedure to factory reset the a 7960 phone running 6.3 SIP software? I've tried holding # when booting the phone and nothing, i can do that on my 8.2 phone but this phone i just got with 6.3 isnt working. Also **# doesnt work either.. -- ~Shaun