similar to: outbound 911 calling

So I have a problem. A customer of mine wants a PBX, owns an office building. I want to sell him on asterisk. He has 4 tenants. I am using my asterisk box to simulate it. My asterisk box has a TDM400P card, not a PRI card. Don't know if it makes any difference. Anyway, I want to route incoming phone calls to different contexts based on the phone number being called. Here is my

Hi, I've configured a new Asterisk 1.6.1 box to replace an old Bristuffed 1.2 Asterisk. Since then, it happens that forwarded calls are not presented the way they used to be. It seems that now, some endpoints are displaying the original caller id (that's what I'm trying to achive), while some are displaying the redirecting number : so if A calls B, B forwards to C depending on where

I understand that most VoIP providers allow for 911 calling but that 911 service is not the same as that available to PSTN.

Has anyone had any experience using asterisk for a 911 call center? Does anyone know of any reason why it would not be suitable? As far as I know all 911 call routing takes place at the CO switch so a regular T1 line should work fine. I understand that there is support for ACD in asterisk and that is should be possible to implement screen pop (CTI). Any comments? Gene Kochanowsky Solution

Still trying to make my Asterisk PBK talk to our Nortel Phone Switch (C15k). Nortel did an upgrade which changed a bunch of things today, so I thought I'd give it another shot. It looks like I'm much closer this time, but still no go. Can't do calling in either direction. Anyone have any ideas? Thanks! Shawn [nortel] host=10.0.0.10 insecure=very type=peer qualify=no

I have a system with two 4 port T1 cards, with 5 PRI's configured. Each PRI is configured as an individual PRI and belongs to it's own group (groups 1-5) This system is handling roll-over from another system, where any error in processing the call on that system results in it being sent here. This mainly results in all calls resulting in a busy being sent for retry here. I then

I have setup as per the monitor example configuration on the wiki site and all works well for an extension dialing 8 then the number. However, if I dial from an AGI script the recording stops after a few seconds. I see an extra answer in the console and suspect that is the reason. Could any kind soul help me to get around this? Extensions.conf.. exten =>

I can't seem to hide and/or set my caller ID from *. I'm using a quite recent (three weeks or so) CVS with an E400P card. I have pridialplan=unknown in zapata.conf and I'm based in the UK. The relevant bit of pri debug looks like this (reformatted to fit 80 char width): > Calling Number (len= 4) [ Ext: 0 > TON: Unknown Number Type (0) >

Here is the setup: SIP/3044 -> SetCallerID(5551212) -> Call out PRI The CDR shows a src of 5551212. That is a lie! The src of that call was not 5551212, the source was 3044! The "translated source" of that call was 5551212. How can I get "real" source of this call and not some faky nonsense? The "reason" behind using the SetCallerID is because if I

OK, got a question on 911. Looking into setting up a couple asterisk servers at a country club, with VOIP phones in each of 100 short-term residential rental units. Approx 100 extensions, approx 24 outside lines. Since everything is geographically at one location, reaching 911 correctly shouldn't present a problem. However, the club wishes to ensure that 911 authorities are able to identify

I'm confused about something. It's the way Asterisk handles the A leg (ie the first party dialed) on an originate command via the Manager Interface. Lets say our originate commands looks like this: ACTION: Originate Async: yes Timeout: 60000 Exten: callback Channel: SIP/5551212 at provider Variable: destination=SIP/8675309 at provider Callerid: 5551212 Context: default ActionID: 849120

NENA i2 The NENA i2 architecture was designed to support the interconnection of Voice over Internet Protocol (VoIP) domains with the existing Emergency Services Network infrastructure. This overview will describe the functional elements and call flow of a VoIP 9-1-1 call over the i2 architecture. The NENA i2 architecture was also designed to utilize existing 9-1-1 voice and data links to all

I have two servers, each connected to the PTSN via PRI. When I call from site A (951-999-9999) to site B (555-1212) and the phone at site B is on the phone, I hear the normal ring tone for about 20 seconds, then the message "all circuits are busy now. please try your call again latter" followed by the congestion tone. Instead, I want this to busy ring and then hang up without any

Does anyone know if realtime extensions allows extensions in the format callerid/extension yet? ie the extensions.conf file allows you to do: 5551212/1000 => exten ... and it matches against extension 1000 when the caller id is 5551212. Last time I checked, realtime didn't support this yet. That's a show stopper for us. -------------- next part -------------- An HTML

AsteriskNOW 1.4.26.2 with a Digium TE205P connected to an ISDN PRI (single span). I'm sure I just have something goofed up in the dialplans? I have a bunch of Polycom 331 IP phones connecting to the server. I can dial the other extensions in the system fine and I can dial long distance outgoing but cannot seem to get it to dial local (7 digit) calls. I see this in the CLI: --

Hi, I'm wanted to do working anonymous calling with my sip provider. To do it, I use SetCallerPres(prohib). The problem: The "fromuser=" parameter overide the value of "CallerID(number)" and do it don't working. Anyone had an idea? Tank's Loic Foucault -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am running asterisk 1.0.1 with OH323 compiled in. We have a 323 trunk to CallManager with a mgcp controlled pri router. When using sip phones (directly registered with asterisk) to call out the 323 trunnk to PSTN, calls timeout after 3 rings. If I answer b4 3 rings - no problem, otherwise I get "no one is available to answer at this time" on the consoel and it redirects to an

This was given to me by a Telco guy in Canada. Talk about a great view of things to come. ESWG Consensus 12-month Report on Nomadic VoIP Technical and Operating Impediments to 9-1-1/E9-1-1 Service Delivery in Canada. PREPARE FOR 911 Executive Summary Emergency Services Working Group (ESWG) recommends on a consensus basis the Commission order the deployment of NENA Interim-2 (i2) compliant

ESWG Consensus 12-month Report on Nomadic VoIP Technical and Operating Impediments to 9-1-1/E9-1-1 Service Delivery in Canada Executive Summary Emergency Services Working Group (ESWG) recommends on a consensus basis the Commission order the deployment of NENA Interim-2 (i2) compliant emergency services components, systems and upgrades to result in the operation within 18 months of enhanced

I am trying to place an analog outbound call from a Sipura SPA-841 through a * server with a TDM400P and 4 FXO's. When I call in from an analog line everything works fine, I can talk over the SIP phone. When I call out, * says: == Spawn extension (from-sip, [phonenumber], 1) exited non-zero on 'SIP/sipphone-d29d' -- Executing Dial("SIP/sipphone-9eb0",