similar to: broken message waiting indicator on Polycom IP600?

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

Has anyone had an issue with the polycom's not discontinuing the mwi chirp even after the message has been acknowledged? -- James M. Milne Nuvio Corporation CCNA - CCNP - CIPTSS - CCIE milne.james@gmail.com

Hello list: I have a very odd problem. Seemingly randomly, my Polycom IP600 phones will ring without a call being placed to it. That is to say, a random phone will ring. Nothing shows up under Caller ID. Even the buttons that light up to show an incoming call do not light up. If you pick up the handset, you can hear the phone ring through the speaker. Hanging up the phone makes it stop

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Hi, At one location we have a user whose Polycom IP430 suffers from erratic reboots. We swapped his phone for a brand new one, but the problem remains. Has anyone seen that?

Hi, I am mostly happy with my Polycom IP600 but it apparently needs to check the FTP server every minute. I couldn't find any obvious setting related to that behavior in the configuration files. Any idea how to curb the IP600's spurious network activity? Thanks, -- Lord, protect me from your followers.

Did you try to boot without lan just the power ... I've had this same problem to and rebooted the device without lan connection -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Louis-David Mitterrand Sent: woensdag 26 januari 2005 11:36 To: 'Asterisk Users Mailing List - Non-Commercial Discussion'

I am wondering if anyone could help me figure out how to turn down the volume on all the dial tones, indications, etc.. and especially the call-waiting CHIRP! I don't want to change the txgain and rxgain because they are working at levels that I would like. However, when voice conversations and voicemail recordings are at good levels then the dial tones, busy tones, etc are way too loud.

I have a quick question... In the previous thread http://www.marko.net/asterisk/archives/0210/0306.html it is mentioned Mark added support for MWI to the chan_zap. Is this in the zapata.conf and if so, if stutter is turned on then the MWI is turned on with it? Geoff

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

I'm trying to make the MWI indicators on my client's Vodavi Starplus DHS phones work. The actual signalling - in-band DTMF from the ZAP interfaces directly to the PBX system - works fine. I can manually tell asterisk to send "#9610" as DTMF and voila, the MWI on extension 10 lights (or goes out.) The question is, how is this integrated with voicemail, i.e. so that the MWI

Hi, I have just upgraded my Cisco 7960 phone to SIP firmware today and I have to say it's working great with Asterisk. At work (which uses Cisco Call Manager), when a voicemail is recieved the read light remains lit until the voicemail is retrieved. Is there any way to achieve the same effect with Asterisk ? Thanks, Paul. -------------- next part -------------- An HTML attachment was

Hi, i wanted to know that if i have a message indicator SIP phone , then MWI will work in ELASTIX ?? Let me know the Details of MWI and how test it. *--* *Thanks & Regards* *upendra* -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20140804/125551b7/attachment.html>

I'm trying to solve a homework problem using R. The problem gives a list of cricket chirps per second and corresponding temperature, and asks to give the equation for the linear model and then predict the temperature to produce 18 chirps per second. So far, I have: > # Homework 11.2.1 and 11.3.3 > chirps <- scan() 1: 20 2: 16 3: 19.8 4: 18.4 5: 17.1 6: 15.5 7: 14.7 8: 17.1 9: 15.4

I have had several cases where the message waiting indicator was stuck in the on state with Cisco 7960 SIP phones. Here are the two cases: 1. Single extension that mapped to a single voice mailbox. Restarting Asterisk or getting a new voicemail then clearing it fixed the problem. 2. Three SIP extensions that mapped to a single voice mailbox. Getting a new voicemail and then clearing it

What is required to get the mwi to work? Is it more of a phone subject or *? I have the mailbox= line in sip.conf, but only one extension is named, and in some of the examples, I have seen that there are two... What is that all about and how does it affect the extensions.conf and voicemail.conf? Thanks again..... Just some background as you start seeing my lists, I just started my own business

Hi, The call waiting indicator do not work for me. I am using a snom200 cwi is switched on in phone-config. Have asked snom, but there are can not help me, because it is working for them. When it is coming in an call while the phone is busy. The phone returns: -- Got SIP response 486 "Busy Here" back from 190.100.200.19 But it should not, should make a "call waiting

I am currently utilizing Polycom IP600 phones and presense. I have placed the hint directives in and everything seems to work fine. But this only works for a short period of time. After about 30 minutes, the extensions do not see when others are on the phone. Has anyone seen this type of behavior before? I am currently utilizing v1.5.2 of the polycom software and the cvs-head release from

Have a strange problem... When a C7960 calls the Polycom ip600, the ip600's first line button blinks, the ip600 display shows the proper callerid, but the phone does not ring at all. If I call the same ip600 from a bt102, the ip600 rings properly. If I call the same ip600 from another C7960, the ip600 rings properly. All phones and asterisk are on the same lan within a few feet. The

FYI for anyone using the dual ethernet ports on a Polycom IP600. I'm using a Polycom IP600 connected to an HP2524 10/100 switch, which has an asterisk box connected directly to it. No VLANs defined or in use. Measured bandwidth: PC -> HP Switch -> Asterisk : actual throughput measured at 94.1 mbps. PC -> IP600 -> HP Switch -> Asterisk : actual measured at 91.9 mbps. The