similar to: Problems transferring calls - Part 2!

im using g729, but the bw usage is ~26 kbps per call, my gateways (cisco) support g723 and the bw between the gateways is ~18 kbps per call. Much better than the ~62 kbps of the g711. if you plan to be a voip provider you "must" go with compression codecs, especially if you want your customers to browse the internet while having a call. i.e. : We give voip phones (grandstream) to our

Are there affordable DIDs (preferably IAX) available anywhere outside the US? I want to use it to meet ICANN requirements for providing a valid phone number, yet pre-empting some of the telemarketing calls my domain registrations generate. (Yes, I asked a similar question about 900# availability before). I'd prefer to have a number somewhere outside the NANP, preferably an asian country.

Hi This is hard work :) I have read the Asterisk Handbook, BudgeTone User Manual, Andy Powell's useful notes, Zac Sprackett's Asterisk Resource Pages and more. I am not a linux newbie but am new to Asterisk. I have failed to find any docs that explain how to get a very very simple, minimal, system up and I am trying to get the following to work: 2 BudgePhone 102D connected on a LAN to a

Hi, I have configured an Asterisk server with TDM01P (1FXO) for testing purpose. The interface I'm using is AMP. I want to configure my extension so that when I dial from my mobile phone to the asterisk line, I want it to transfer the call to any extension, say 3042 and after a particular number of rings, transfer the call to voice mail so that I can record my message. My Zaptel.conf is as

Hi ALL Have installed asterisk@home 1.0 On FWD DID's, appears that 2 calls are generated to the inbound extention. I have confirmed this on a number of friends boxes also. Does anyone have a fix for this ? I set the DID simply to a custom context and it did the same... Anyone have a way to fix this ? Here is the output...... -- Accepting AUTHENTICATED call from 65.39.205.121, requested

Hi, guys, For my server, if i use my handphone to call in the PSTN line by TDM400p card, the server could not receive the caller id correctly. anyone knows the problem? I am currently using asterisk 1.2.14 with freepbx 2.2.1. The CLI is as below, "Caller ID name is 'zap1' number is '4521'" , this 4521 is one of my FXS zap extension created. dialparties.agi: Starting New

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

OK, i've got asterisk @ home 1.3 up and running with Broadvoice. BUT I have one nagging problem to sort out. When you call my BV # the calling party gets no ring indication, just silence until either I answer the phone, or the call bounces over to voicemail. below is the console output when a call is recieved. what am i missing here? thanks Bernie -- Executing

Running Asterisk Head 1.0.9. Below is a trace of a call delivered to my system which had no caller ID. For some reason, dialparties.agi shoves the incoming provider's IP address into the caller ID so you never have a call that is screened for PrivacyDirector. Is anyone else seeing this issue as well? Have I missed a patch? This call shows on the display with a name of "Unknown"

I am having a problem with the Call Queue Feature. If I let a user into the Queue prior to an agent being available for them to take the call, they experience the following: 1) they hear that they are the first in line 2) when the agent finally logs in (the caller on hold in the queue is sent to the users phone) 3) the AGENT is still in the login phase hearing that they are "successfully

Hello all, I have been posting some questions about this problems that I cannot yet solve, but I think I have a better diagostic, so maybe someone can give me a clue why it is happenning. I have Asterisk + AMP configured as a PBX with a Customer Center Queue with 4 agents that login/logout dinamically. If there are no agents, queue timesout and gets derived to another queue that somebody

I have Asterisk 1.2.29, Zaptel 1.2.24 and Freepbx Setup for a queue up to 15 agents through a PRI line, it was working fine for more than 1 year, suddenly, when there is a load on the queue, the asterisk service disconnects and the calls are dropped. And the service starts again after few seconds, and so on. I am not using fax. I checked PRI by zttool and there are no alarms. The cdr logs

Hi, I set up a ring group. I would like for people who select a certain voice menu option to ring a list of extensions (I have just one extension in there at the moment) and if it doesn't answer to go to an extension's voice mail. I am using a version of asterisk from CVS, last updated a couple of weeks ago. This line in extensions_addtional.conf sends the call to ringgroup 3 if

I don't succed in getting callerId on incoming calls on a zap trunk. I am using a zaphfc card When a call is received, one line in asterisk pbx says -- Executing SetCIDName("Zap/32-1", "") in new stack second parameters should be the caller ID, but it is not set The callerid is not hidden at source, so I think that is some kind of setting in zapata.conf I am using

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

Hello all, I've installed AAH 1.1 on my VIA C3 powered mini PC. I've made the necessary changes to the * makefile, so the compilation went well. The first thing I did was configuring two extensions from AMP, namely 200 and 201. Then I installed X-lite on two PC's and configured them with one of the extensions: System settings - SIP proxy - Default: Username: 200 Authorisation user:

Hello, I have setup a test server with asterisk/AMP and have several 7960's connected to it. The asterisk server has a public ip and all the 7960's are behind nat'd routers. When I try to call from extension to extension I get directed straight to voicemail. I do not have any cards installed and instead direct everything to an Ondo server. I have been told it's not an AMP

I have installed my first Asterisk implementation using the Asterisk@home ISO. I am using the SJPhone software. Using the setup page, I have been able to configure two extensions. Whne I dial from one to the other, the other does not answer even though it is registered. Watching the log in the CLI, I can see that recorded messages are being played;: == No one is available to answer at this time

Hello List, I am having a strange issue with a trixbox system we installed for a client, and I would appreciate any help on this one. The issue is that occasionally when they go to answer an inbound call from the Sangoma A200 - there is no one there, and they are presented with dial tone. The calling party is hung up. A bit of background: The client actually has two systems install (one at

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP