similar to: g729 problem

I find that DTMF does not work reliably if jitterbuffer=on for certain IAX providers. For instance, DTMF tones are missed entirely about half the time when I dial into an exgn.net account. However, it always works fine for an unlimitel.ca account. Someone else has seen this too: http://bugs.digium.com/view.php?id=6011 Can anyone suggest a workaround (other than jitterbuffer=off)? - Mike

Ok Dan, try this... I was able to get this to work behind a NAT and with ip address authentication. [global] type = global debug = yes [transport1] type = transport bind = 0.0.0.0 protocol = udp *local_net=<yourlocalnet I.E. 10.10.10.10/24 <http://10.10.10.10/24>>external_media_address=<your public ip address>external_signaling_address=<your public address>*

Hi, all. I'm probably doing Something Dumb(tm), so please feel free to point out whatever I'm missing, no matter how stupid. Anyway, I've got IAX set up to Vitelity. When I try to call my DID, I get: Rejected connect attempt from 64.2.142.19, who was trying to reach '6031234567@' This leads me to my first question -- why doesn't it show a context? (My second is,

I have a Vitelity DID which generally works, but calls from a particular caller do not reach it. Vitelity has thus far disavowed any responsibility for working through this problem. I recognize that some action might be required by another provider which is outside Vitelity's control, but it seems that they should at least be trying to help resolve the problem by helping me determine

On Mon, Dec 15, 2014 at 9:48 PM, Dan Cropp <dan at amtelco.com> wrote: > > Thanks George. > > I will correct my local_net in the morning. > > Vitelity chan_sip settings I have working, do not have a fromuser. > sip.conf settings... > > I think you can actually specify anything, it just has to be populated with something other than a sub-account username. >

On Mon, Dec 15, 2014 at 3:33 PM, Dan Cropp <dan at amtelco.com> wrote: > > Hi George, > > > > Thank you for looking into this. > > This is behind a nat? > > > Just to be clear...both the pbx and local endpoints are behind the same NAT? > [global] > > type = global > > debug = yes > > > > [transport1] > > type = transport

Not sure why, but Vitelity changed the settings to IP based authentication on me. Here's the new sip.conf settings they sent me. type=friend dtmfmode=auto host=64.2.142.93 allow=all nat=yes canreinvite=no trustrpid=yes sendrpid=yes When I use these settings to originate calls using the sip.conf they sent me, everything works. Action: Originate ActionID: S8 Channel:

On Mon, Dec 15, 2014 at 7:34 PM, Dan Cropp <dan at amtelco.com> wrote: > > I am not sure if I entered the correct settings for the transport > information. > > For the local_net, I entered my local ip address, but no mask. I will > check with the network admin so he can verify the settings I entered. > > > You need the network and mask. For example if the ip

On Mon, Dec 15, 2014 at 3:54 PM, Dan Cropp <dan at amtelco.com> wrote: > > Yes, everything is behind the same NAT. > > > > For the application I?m working on, the only endpoint is the endpoint to > Vitelity. > > We use AMI to Originate calls from Asterisk endpoint through Vitelity to > phones. > > After that, we control the call through AMI to perform the

On Mon, Dec 15, 2014 at 2:08 PM, Dan Cropp <dan at amtelco.com> wrote: > > Today, I tried the same behavior on Asterisk 13.1.0 and Asterisk 12.2.0. > > > > Same problem is happening with both of them. > > > > Could this be caused by PJPROJECT 2.3? > > > > Anyone have any suggestions for what I can try? > > > > My boss is giving me until

Vitelity seems to be offline to both IP and voice traffic. Is there any place to find out what their status is? Roger Marquis

I have a Asterisk server setup and I am able to connect to the server using a soft client 'x-lite' and call and leave a message on my second extension 102. I have setup a Vitelity account and add what I believe to be the correct information to my sip.conf and extension.conf. I would like to setup incoming and outgoing calls with voicemail support. I've searched all over but many of the

Here's an update... My network admin would not turn off the ALG because it would cause several other problems to other phone systems we have. He looked at the sip trace. What he found is the PJSIP trace showed a different IP address than the older chan_sip so he had me change the aor contact to outbound.vitelity.net At this point, it seems to be working (and this is going through a Cisco

Dan Cropp wrote: > I corrected my local_net setting (based on advice from network admin). > > I have tried several different values for the from_user and still have > the same problem. > > Asterisk receives the OK from Vitelity. > > Asterisk sends the ACK (without a Contact header). A Contact header is not required to be in the ACK. > > Vitelity doesn?t seem to

Hello List, Since I'm looking for a new VoIP provider for US origination/termination, I will very appreciate if you can chare your experience with Flowroute, Vitelity and Voip.ms Thanks in advance! Elder D. Arohuanca dCAP 1497 Lima - Peru -------------- next part -------------- An HTML attachment was scrubbed... URL:

On 8/9/16 12:40 PM, Matt Fredrickson wrote: > On Mon, Aug 8, 2016 at 9:25 AM, Tammy Firefly <tammy-lists at wiztech.biz> wrote: >> Hi All, >> >> We have asterisk 11.23 running sip to vitelity and from there IAX trunks >> split off to where they need to go. We are having a problem getting >> chan_sip to quit ignoring re-invites from Vitelity. Our side ends

Any vitelity customers with pbxinaflash boxes? I'm able to call in-house, but failing to make outbound calls. My assigned server at vitelity is not reachable. I can ping to my ISP OK. Any help appreciated. Such as actually how to make email contact with support at vitelity. They're not responding. Thanks, Tom

Hi All, We have asterisk 11.23 running sip to vitelity and from there IAX trunks split off to where they need to go. We are having a problem getting chan_sip to quit ignoring re-invites from Vitelity. Our side ends up sending a reinvite which their side & they do not support us sending a reinvite. Ive tried: canreinvite=no which was supposedly replaced by: directmedia=no Can anyone shed

Just emailing the list to see if anyone out there has used Vitelity? If so what has been your experience with service, support etc? Thanks Curt

Hello, I?m trying the g729 codec for testing pourpose. Whe I try to make a SIP call from a phone using g729 codec to another phone using another codec, when the destination phone answer, the call hangs up. this happend in both ways. In the asterisk console I get. Mar 4 13:11:35 NOTICE[24572]: channel.c:1724 ast_set_write_format: Unable to find a path from gsm to g729 What does it mean?