similar to: ISDN + chan_capi

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Hi all, I've been playing about with Asterisk for years now on and off, just SIP to SIP calls, using FWD and suchlike. I'm moving house at the beginning of September and have decided to build an Asterisk based system for my home office. I'm in the UK and wonder if anyone can give me advice on lines and hardware to use. Had planned to go with an ISDN2e line coupled with a BT

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello, i wonder why i didn't find a solution for this problem yet, because it seems very common: I have an asterisk server with an AVM (Fritz) ISDN-Card (BRI), and some SIP-Softphones which i can call from outside by calling the phonenumber of the Asterisk-Server and then dialing the number of the SIP-Phone. If I make a call from a SIP-Phone into PSTN, only the MSN of the asterisk-server is

Hi, Reading http://www.asteriskguru.com/tutorials/bri.html , it seems PtP is the way to connect businesses but if you read http://public.swbell.net/ISDN/connect.html you would think the opposite. Can anyone elaborate a bit PtP or PtmP respective advantages ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hi, I am struggling to get plain Cologne chip cards to run in NT mode, runs nice in TE mode despite the error message: login as: root root at 192.168.2.22's password: Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50 Welcome to Elastix ---------------------------------------------------- misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi, At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point to multi-point mode. Here (France), most small PBXes are connected to ISDN through BRI trunks in PtmP (don't know why but it seems the general case). So this NT-PtmP function would be very helpful to easily slide an Asterisk box between an existing PBX and the network. Does the same case apply elsewhere (UK,

asterisk-users at lists.digium.com has now been added to the filters white list! Anyway, 100ohm termination isn't required for ptp - but is required for ptmp. I know the DAHDI package(s) no longer include make b410p - hence the reason it is included in the docs.

Hi, how can I set up multiple ISDN controllers with chan_capi, so that every controller has its own configuration (MSNs to listen etc...) ? I know I can configure "controllers=1,2" in chan_capi's capi.conf but then the controllers have the identical configuration and context within asterisk. My setup: I have 2 BRI-controllers (in one AVM C2). 1. BRI: point-to-point, Number:

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

... Thanks, anyway for telling as at least, it reflects your needs. > > > You want NT PtMP and i second that, > not being limited on the asterisk > side is a must in the > telephony ecosystem, since the legacy PABX aren't alwsys easy to > reconfigure. > > _______________________________________________ > -- Bandwidth and Colocation Provided by

I have 10 msns on my isdn bri incoming (AVM Fritz, chan_capi 3.5) When i set in capi.conf [interfaces] msn=1,2,3,4,5,6,7,8,9,10 incomingmsn=* controller=1 softdtmf=1 accountcode= context=tcom-in echocancel=yes devices=2 Only msn 1,2,3 are working. What can i do? Thanks Jens