similar to: sipura 3000 mwi stutter problem

Off topic but I am after a DECT phone to connect to my sipura 3000 that has a FSK VMWI light or flashing envelope on the LCD screen. Any ideas Chris

Anyone else got a Sipura 3000 in the UK? Apart from CID not working it also seems to not notice any of the line state changes on the PSTN when the remote party terminates the call. It only recognises the offhook signal which gets sent much later. Chris

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

Let post this question.. Because I must be real slow... The following is my config on this... group=1 context=default signalling=fxs_ks channel => 1 context=local signalling=fxo_ks callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=1.5 txgain=1.5 immediate=no musiconhold=default usecallerid=yes

This is a wierd one. Can't figure it out. I have an SPA-3000 at the house handling my incoming line. It's setup to direct the incoming call to asterisk. Works great 99% of the time. A few times a day, I'm getting calls that ring once internally and are then hungup. I managed to get a detailed log [1] of what's happening today and it looks to me that the SPA is acting wierd.

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

Hi.. I am about to replace my aging Nortel Venture system with an Asterisk system and 6 Polycom IP 501 phones, and a couple sipura 841's for less used areas. We have 3 phone lines here. One is SBC, one Vonage, and one Voipjet... One hangup is that I can't figure out how to pass through a voicemail waiting indication from SBC. This is important because my wife and her family all

This may not be the right place to ask, but I have an annoying issue with a Sipura/SPA1000-2.0.10(e) ATA device connected to an Asterisk box. (The system is remote to me, so I've only been able to observe this by dialling into a VoIP phone on-site, then run commands on the box remotely!) First of all it's all working fine connected to an Asterisk box and the user can make/take calls

I have many remote locations that dial into a central server to retrieve voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a local (to them) Asterisk server that dials the main server thru IAX. I have trained them to check their voicemail via the emailed WAV file, however some of them are, how shall I put it, idiots*, and insist that they *have* to have the MWI indicator

I dont recall the SPA-941 playing a stutter tone in the previous firmware but it is driving me nuts, anyone know where to turn it off? Kerry Garrison Director of Technical Services Tech Data Pros - Orange County's Mobile IT Service Provider (949) 502-7819 x200 - <mailto:kerryg@techdatapros.com> kerryg@techdatapros.com <http://www.techdatapros.com/> http://www.techdatapros.com

I figured out what was going on with the lack of/stuck on stuttered dial tone. Apparently, there are two voicemail directories being referenced: /var/spool/asterisk/voicemail/default, and /var/spool/asterisk/voicemail/local. The sip phones were using /var/spool/asterisk/voicemail/local to dump VM messages into, yet the MWI looks at /var/spool/asterisk/voicemail/default. Does anyone know why

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

I think I have something misconfigured regarding voicemails. They work great, I have this setup: Sip.conf [ext1] Context=phones Mailbox=201 Voicemail.conf [home] 201,password,name,email@mail Voicemail delivery and all works great but when I check sip extension ext1 (analog phone using a Granstream ATA 286), the stutter tone signaling message waiting does not work. Anything wrong with

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

A while back I converted back to static conf files from a database setup. However I decided to tackle it again. The problem that I was experiencing, was, there was no stutter tone on my sipura 2000 or 3000 when there was a voicemail left at either extension when I was using mysql setup for peers and voicemail. I have 2 contexts... home, office in my voicemail configuration I now use

I am trying to set up the Message Waiting Indicator (stutter tone/light) so that my cisco ata-186 will let my phones know there is a message waiting. However this does not seem to be very well documented. I found this on wiki mailboxnumber@context ... where does that go? Do I put it in my SIP.conf definition for my cisco ata, or where. In my SIP cisco definition i already have a

My grateful thanks to whoever can guide me in implementing this... I have a need to place calls via Asterisk Manager Protocol to a legacy PBX and twiddle its MWI lights. By some means I get notified that an MWI light has to be changed. Via AMP: 1. Send an ORIGINATE command honking up an incoming port on the PBX via a TA804. a. I presume that the TA804 should be a SIP channel. yes/no? b.

Using a TE410P with Zhone 24FXS channel banks to power standard analog phones I can't seem to find out if it's possible to support FSK or voltage type message waiting lamps. I don't want to use stutter dial tone because of the dramatic difference in per phone cost. TIA

asterisk-users-request@lists.digium.com is believed to have said: >I don't mean to be rude to everyone who responded to this question, but >I think that everyone is answering the wrong question. The point is that >the message waiting indicator doesn't light up, at all, ever. All that >happens when messages are waiting is that the display blinks and the >phone gives a