similar to: Registering with IAX provider

I didn't get any response at all to my last "request for status" on IAXTEL. So, when this happens, I attribute it to one of a number of things: 1. No-one knows. 2. No-one cares. 3. Everyone knows, but are too busy to reply. At any rate, my investigative side kicks in and I began searching thru the digest's I've gotten, looking for references to IAXTEL. Mostly it is

I find IAX connection with FWD very unreliable so I think I'll have to roll out my own "SIP Express Router" as I want to communicate with few SIP clients. So I hope this the right solution. I'm new to "SER" and to my understanding "SER is like a "road-map" it tells the SIP Clients where they are so they can communicate directly with each other without

On Sat, 2005-06-18 at 13:17 -0700, Matthew Asham wrote: > For what it's worth I use a residential Shaw connection and have no > problems with IAX registration nor SIP to our Asterisk PBX elsewhere on > the 'net. When I had a dynapic IP connection with shaw, there was not problem either. I just changed to static and IAX can not connect. How can I test it? iax2 show registry Host

How do I solve the problem with between patterns: _1800 _1NXX I would like all numbers 1800, 1877 etc to go through iaxtel but all other numbers 1xxx via voipjet Example in my extension.conf I have: [iaxtel] exten => _1700NXXXXXX,1,Dial(IAX2/xxxx:xxxxx@iaxtel.com/${EXTEN}@iaxtel) exten => _1888NXXXXXX,1,Dial(IAX2/xxxx:xxxxx@iaxtel.com/${EXTEN}@iaxtel) exten =>

I just changed the from DSL to Shaw Cable (static IP) configure the firewall but now asterisk I can not register with FWD nor VoipJet calls going out. I am using IAX with FWD Did I missed to change a setting? I don't think there is any though. I am on shaw extreme connection; I just talked shaw tech. and they are not blocking any port - I was told. So why IAX will not register with FWD and

I have an incoming 800-number over IAX from Teliax and I'm experiencing the large packet loss on connection. When a call comes in there is no ring tone and the first few words of the welcome message are cut off, regardless of the delay I set. Standard call (not 800-number) coming over IAX with the same provider works just fine only the tall free number. So it seems there are some packet loss

Been meaning to ask this for some time... no big deal, but curious. I have a single register statement in my iax.conf for iaxtel like: [general] port=5036 register => npi:mypassword@iaxtel.com <snip> However, when I restart *, I see: Registered to '69.73.19.178', who sees us as 205.221.193.101:5036 Registered to '69.73.19.178', who sees us as 205.221.193.101:4569

Hi All, Sorry if this has been covered in the past; I've tried searching the archives, but haven't had any luck finding a similar problem. Basically I have problems when using IAX2 (which I now understand is just IAX). I have three IAX connections setup - VoicePulse, IAXtel, and an Asterisk IAX<->PSTN termination provider here in Sydney (ATP) If I try to use the CVS STABLE version

I'm just curious why Sipura isn't using free IAX protocol with their devices instead of SIP? With IAX NAT traversal would have been easier, so why are they using SIP. Is there any politics in it? -- #Joseph

Hello all, Can someone send me a current working example of what the entries need to look like for iaxtel and the iax.conf file inclusive of the register line? It's been quite awhile since I have done anything with iaxtel and I need to do a little bit of testing. Currently it appears that I can make calls out to iaxtel fine however inbound seems to be another question. I see 2 iaxtel

Has anybody tried NVFaxDetect Fax detection for sip SIP/IAX channel? There is a new application from Newman Telecom for fax detection. http://www.sineapps.com/news.php?rssid=575 Current Asterisk Fax detection doesn't work for me as I don't have Digium cards; I'm using Siupra -- #Joseph

I'm attempting to get two Asterisk 0.4.0 PBXes to communicate with one another using IAX/IAX2 trunks. I've managed to get a semi-functional NAT Firewall working as a PBX (with Asterisk running directly on the firewall itself), but there are issues with bind()ing to various interfaces which is causing outbound SIP issues. To get around these issues, the idea is to do something like

I tried to connect my * to IAXtel, but i always get this errors. chan_iax2.c:5849 socket_read: Registration of 'mnetwork' rejected: Registration Refused On dial a iax number i get: chan_iax2.c:5526 socket_read: Call rejected by 69.73.19.178: No authority found chan_iax2.c:5528 socket_read: Immediately destroying 3, having received reject chan_iax2.c:2411 iax2_hangup: We're hanging

I have a problem with my asterisk@home installation (configured with AMP) My question is this, can you have different ports for different contexts within IAX? [Faktortel] port = 5036 ; Port to bind to bindaddr = 0.0.0.0 ; Address to bind to context = default ; Default for incoming calls allow=all ; Allow all codecs register => XXXXX:XXXXX@iax.faktotel.com/EXTEN

I have, in iax.conf the register statement: register => username:password@iaxtel.com This causes registration attempts to iaxtel.com for both IAX and IAX2. Every once in a while there is a packet for port 4569 keeping the IAX2 registration alive. This is fine. But, I have a barrage of registration attempts to iaxtel on port 5036 for IAX. Every UDP packet is answered with an ICMP packet

Hi all, I'm trying to get IAX2 trunking between two * boxes and am having extreme difficulty :) What happens is when the sending * server (the one initiating the call) receives the ACCEPT back from the receiving server it immediately replies with INVAL. I've checked the code and it seems to be not matching the accept packet with the relevant item in the iaxs array due to the following

When I try to call iaxtel it goes to codec ADPCM even though I have define in iax.conf gsm Call accepted by 69.73.19.178 (format ADPCM) -- Format for call is ADPCM My settings: [general] port=4569 register => xxxx:xxxx@iaxtel.com bandwidth=high jitterbuffer=no tos=lowdelay [voipjet] type=peer host= xxx.xxx.xxx.xx secret= xxx auth=md5 notransfer=yes context=incoming disallow=all ;

Help, I'm stuck. Lost in the woods. I have one Asterisk running on FreeBSD outside on the Wild Internet. One on the safe inside, behind a NAT firewall. The inside server registers with IAX to the outer one and can place calls. The outside one can't register to the one on the inside, since it can't be reached on the private network. Now to my problem: * How do I dial from outside to

Hello, I updated CVS and nobody can call me any more with my IAX number 17007591228. I can only call other number but nobody can call me. This is what I get on debug when I call myself: -- Executing Dial("SIP/1011-7424", "IAX/bartosz:password@iaxtel.com/17007591228@iaxtel") in new stack -- Calling using options

I've asked this before but I don't recall seeing anyone respond. Maybe the answer is so simple that it should jump right out, but its not. I've got three iax connections defined, two working fine (including one to iaxtel), and one that is somewhat intermitant. If I do a cli 'iax show registry' and 'iax2 show registry' I see "both" iax and iax2