similar to: PRI concentrator

I'm posting here in case anyone else runs into this and needs some help. I'll probably update the voip-info Wiki pages on Toshiba integration in a bit. Asterisk 1.6 makes things a bit easier than what is on that page. I'm integrating an Asterisk server with a Toshiba Strata system at my office. Right now, it is driving some VoIP phones (Cisco ATAs with analog phones plugged into

I am currently working on an Asterisk test system, and will be presenting a demo to the Board of Directors tomorrow night. I want to make sure I have all of my ducks in a row. The Asterisk system will be used to replace a Norstar MICS. The location has two PRI's coming in, with a few hundred DIDs. I know how to make * use the DIDs incoming, and I know how Nortel uses the DIDs. Now for the

I'm trying to get to the bottom of an issue with key authentication on AIX and I'm not sure I believe IBM's answer so I thought I'd post here to see what answer I'd get from the SSH side. We have three different methods of authentication - local, VAS (AD), NIS. On our Linux and Solaris servers it's very simple to set the authentication order with nsswitch.conf and SSH

I've got a system I'm putting together to handle IVR calls with * I have one head system that terminates two PRIs. It routes the calls from the PRIs to * boxes using IAX I'm planning on having four or five * boxes. The * boxes run AGI scripts to process the IVR calls. Can I load balance the routing if I have five calls each of the IVR * boxes gets two call and the next call would go

Hi All, i would like to know if anyone has done or having idea regarding PRI terminations in asterisk. i have a requirement where i need to support 80 PRI in one machine i have found a machine which have 10 PCI slots available now i am thinking of arranging 8port sangoma card in this pci slots so i can arrenge 10 card in that. is it possible to run system like that ? is it good idea , can

Anybody have suggestions on having a 56K dialpool and VOIP connections with an Asterisk box over the same set of PRIs? We've done the PM3 with PRIs for just dialup, but are looking for a way to integrate our Asterisk box and move our voice calls onto the same PRIs. Ian -- Ian White Victoria Free-Net Association email: iwhite@victoria.tc.ca http://victoria.tc.ca/

Thanks Alex, some great ideas. I think, however, I'm leaning towards Asterisk at this point- since I have quite a bit of experience there, and very little with SER. At this point, I'm wondering from a dimensioning standpoint, what kind of capacity my machine will have (Dual Core Xeon 2.4GHz 4GB RAM). As I said, I don't plan to do any transcoding. I read the voip-info page on

There's now a plugin called lazy_expunge in CVS. Instead of EXPUNGE expunging the mails directly, they're moved to a mailbox with same name in another namespace where user can still copy the mails back. Also DELETEd mailboxes are moved to another namespace. See http://wiki.dovecot.org/Plugins/Lazyexpunge for more information. This is similar to Cyrus's two phase expunge:

You are correct... No glare on a PRI W. Kevin Hunt CCIE #11841 www.huntbrothers.com -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, May 25, 2004 3:26 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] "Glare" condition - How well does asteriskhandle?

I currently have a single PRI however we are getting a second PRI, and the provider (qwest) wants to know if our PBX supports GSAS (they say its a redundant d-channel technology but searching on google for GSAS reveals less than nothing). I've set something similar up before on a cisco 5350, where if one of the PRIs fails, all of the calls destined for either PRI will be routed down the one

We are doing this with the latest spandsp, iaxmodem and hylafax. Seems to work very well for us so far. -Jonathan > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Michael Gaudette > Sent: Tuesday, March 21, 2006 3:34 PM > To: 'Asterisk Users Mailing List - Non-Commercial

Hello, We are working on implementing a solution for a medium service provider. They were previously using a Cisco AS5300 gateway with some PRI trunks to receive modem calls, then route them out the Internet. The Telco they were buying the trunks to discovered this configuration and restricted them due to legal conventions, and stated that in order to continue doing this, they would have to talk

Hey folks, I have a T100P card with a PRI; when doing outbound dialing over the PRI, I can use SetCIDNum(2024561414|a) to force caller ID to display as "The White House" on a land line. This is apparently done as a reverse lookup by Verizon, as I do not hand the PRI the words "The White House" -- 202-456-1414 is an actual White House number. Using SetCIDName("Flying

Hi everyone, I'm new to the list, so I apologize if this is a trite question. We're an ISP with a barely used PRI, and also currently use asterisk with POTS service on an audiocodes gateway. We have a notion that we want to take on a new revenue stream, with our model being as such: 1) Convert one of our PRIs into a two way voice/data bundle. 2) Plug this PRI into a piece

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

Hello, we have a PRI (E1) to a carrier and a second one to a legacy PBX: DTAG ---pri---- * ------ Hicmo (PSTN) | | Sip and more Many normal inbound calls are direcly routed to the hicom. Outbound calls from the Hicom go through LCR and then to PSTN. Inbound faxes are working, but outbound faxes from hicom to pstn are

hI, Trying to understand how to setup two PRIs in sip.conf. Using Asterisk 1.4.23. I have a provider giving me two PRI (different rate centers) through SIP. Both PRI comes in from the same IP on the provider side, but go to two different IPs (both on the same box) on my side. How can I setup two different SIP peer, one for each of the PRIs I get, if all I can use to differenciate them

Hello, I have a Lucent MAX TNT, (DS-3, 672 modem ports, 28 PRIs). I'd like to be able to direct an inbound fax call into my TNT, have it answer the fax and send the image file over to Asterisk, or some other system to deliver to an e-mail address(s). I'm not sure if I need Asterisk to any of the call control or not. I'd also like to setup a print queue and have outbound

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

Hello, I have a crossover PRI(Asterisk server to PBX) and a regular telco PRI T1 line and currently have echocancel=yes and echocancelwhenbridged=yes on those spans in zapata.conf. I was discussing CPU load with another Asterisk user and he mentioned that PRIs don't need echo cancelation and that turning it off will reduced CPU load on the server. I checked many sample configs and the