similar to: R2/MFC Mexico FREE calls to test chan_unicall

>any feedback would be awsome, the idea is to fill in the 30 channels of >the E1 all at the same time and see how stable it can be > > ----- Original Message ----- > From: "Miguel Cavazos" <miguel@cavazos.com.mx> > To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" > <asterisk-users@lists.digium.com> > Sent: Wednesday,

Miguel, How many simultaneous calls (incoming and outgoing) you did ? Kind regards, Miguel Date: Sun, 3 Oct 2004 11:21:04 -0500 From: Miguel Cavazos <miguel@cavazos.com.mx> Subject: [Asterisk-Users] Working E1 MFC/R2 M?xico !!! To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users@lists.digium.com> Message-ID:

Steve, Do you know if there are many differences between the Mexican and Brazilian variant ? Kind regards, Miguel Antonio Date: Tue, 05 Oct 2004 22:51:53 +0800 From: Steve Underwood <steveu@coppice.org> Subject: Re: [Asterisk-Users] RES: Working E1 MFC/R2 M?xico !!! To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users@lists.digium.com> Message-ID:

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

I have a customer that is complaining that any call coming in from Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel 1.4.3 and all the MFC/R2 patches and libraries. All other calls go out and come in, just Nextel seems to have this problem. The phone company technician connected a PBX emulator on the line and that one could receive the calls from Nextel. The E1 is provided

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Hello list, I was going to buy this weekend a Wisip from http://www.pulverinnovations.com/, but jeff got out of stock and he wont have Wisip for the next 3 to 4 weeks. So I start searching for other wifi phones because I was really upset about it and I found IPC5000 from http://www.fahdtel.com/sip_phones.htm, I liked so much the pic that I email the guy and he send me the PDF with all the details

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

Hello. I'm trying to setup MFC/R2 signaling, but chan_unicall fails at loading with this message: --- Unable to load module chan_unicall.so Loaded /usr/lib/asterisk/modules/chan_unicall.so => (Unified call processing (UniCall)) == Parsing '/etc/asterisk/unicall.conf': Found 061213-075938 ERROR[11454]: chan_unicall.c:3361 mkintf: Unable to open channel 1: Success here = 0,