similar to: T1 Timing Slips

Hi Everyone, So I have been further exploring the integration of our asterisk server and our lucent definity g3si system. I took the suggestion of setting up an isdn-pri line added the two way tie trunk and the signalling group, but can't seem to get the PRI signalling working on the asterisk correctly. I've set pri type to network on the lucent, and pri_cpe in zapata on the asterisk, but

I've successfully integrated * to a Definity G3SI PBX via PRI. On calls from the * box to a Definity display telephone a umlaut over an I appears at the beginning of the caller name on the Definity display. Anyone seen this before? Thanks... Bud

Hey everybody, I'm looking for some information that I'm not finding by searching the 2004 Asterisk archives. I'm currently playing with a Digium T100P card and 2 Grandstream phones, things are working well. I wanted to move on to linking our Definity G3R Rev 8.2 to the T100P. Everything that I've read so far shows that you need a TN464 to accomplish this. We have a TN767E

We have had quite a bit of success with our T100P and TE410P cards interfacing to Nortel Meridian PBXes and also to a Livingston Portmaster 3 using ESF/B8ZS and various combinations of E&M wink and ISDN PRI (usually in 5ESS mode). In the near future, I may also need to interface to a Definity via a T1. I was planning to use PRI--is that an option for you on your switch? -----Original

Hi everyone, We have been working with Asterisk for a while now and would really like to expand its capabilities by fully integrating it with our Definity g3si and are wondering about other peoples experiences with similar setups. Thus far we have only been able to achieve a partial 1 way integration, but ultimately would love to route inbound voip calls to the asterisk out of the lucent.

Just some clarification here. On Monday, June 30, 2003 12:04 AM, Steven Critchfield [SMTP:critch@basesys.com] wrote: > > As for slips and bipolar violations... > T1s are just high speed serial lines. A sleep is when you loose sync > with the far side and when you see a 1 come across the line, you may > not > know which bit it was for. A slip is when one end of the circuit is

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

What an ACTIVE newsgroup! I'm in the early stages of researching Asterisk. My current environment is a small college (~1000 sets/~400 student sets), Avaya Definity G3si/Seimens Rolm Phonemail. As you can imagine, the maintenance, licensing, and equipment costs are HEFTY. So.. are there any small colleges/universities using PBX or Voicemail? If so, I'd be interested in your migration

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

This afternoon I finally figured out more with regarding to a strange clock-slip problem we have on our asterisk box. We have two TE410s, in E1 mode: TE410P version c01a009b They have their own interrupts: 66: 781648298 783747388 IO-APIC-level t4xxp 233: 253890977 1311504670 IO-APIC-level t4xxp They have their full 31 channels: span=3,0,0,ccs,hdb3,crc4 bchan=63-77,79-93 dchan=78

Hi, I just got a T1 interface for a AT&T (became Lucent) System75 (uses same cards as Definity). I would take a crack at making a cable but can't determine the pinout for a cable and it is not apparent from the board. Asking you guys makes sense as one of you may have one of these systems. The cable has a amphenol male D50 connector on one end and probably a rj45 on the other. I also

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

We are running Asterisk version 1.4.23-1, libpri-1.4.9 and zaptel-1.4.12.1 and two Digium TE220Ps. Debugs are set to 10. We have a T1 PRI connected to the telco. Over the last 4-5 days, we have getting Yellow/Red alarms coming from the T1 PRI. The other two ports in use are connected to internal test switches (Avaya Legend/Avaya Definity), and are not showing any errors.

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2, which seems to work quite fine, but I continously receive the messages "D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few seconds interval. Why is that? Bri intense debug log and configuration files below. I don't need ztdummy or zaprtc, do I? I get some frame slips as well,

I've made some modifications to zttest in order to use it as a frame clock accuracy tester / slip detector. I'm not certain if that was it's original purpose, but it seems that a lot of folks try to use it that way. The result is something that I'm calling ztclock for now to help avoid confusion. I'm including the source at the end of this post. You can compile it by placing

Calling all Definity admins, Got a few questions about Definity -> Asterisk interoperability. 1) What are the options for integration? Can I hand off extensions from the Definity and vice versa? 2) Anybody have any working configs they would like to post? I've found and read the legacy integration on the wiki about the two systems. I've also googled and found a few threads that were

Yes, I can make a call on that extension from other definity phone, if you mean it. -----Original Message----- From: Ken Godee [mailto:ken@perfect-image.com] Sent: 30 ÉÀÌÑ 2004 Ç. 19:14 To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Connecting Asterisk and Avaya Definity By E1. Incoming work, but not outgoing Roman Bessyadovskii wrote: > Hi All. > > I connect

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the