similar to: "Telco power supply" with digium card TE410P?

hi all, i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and connected it to a primary line. My telco (eTel) only told me that they are using hdb3 and crc4. So i still don't know which coding i have to use (cas or ccs) - and what timing options i have to use. Have someone already get a card like this up in Austria with a line from eTel or from the telekom Austria ? Another

I've just encountered an odd problem with our Digium TE410P card and was wondering if anyone has experienced something similar before. We utilize all 4 ports with 2 of them connected to the PSTN as E1 with the second 2 ports connecting to a device which accepts T1. We are essentially acting as an E1 to T1 converter. This machine has been operational for close to 6 months without a problem.

Hi, one short question: Is it possible for the zaptel driver to deal with multiple phone numbers on one single E1 PRI line? I could make my carrier route +49 xxx aaaaa-zzz and +49 xxx bbbbb-zzz and others down one single PRI trunk to our asterisk box terminating in a Digium TE410P. Does the driver handle this and can I put calls coming in all on the same physical interface put into

Hello, I am looking to buy a large number of TE410P cards for a big international project. I have studied the documentation and zaptel.conf and as result I have the following questions: 1. How do you switch the card from ISDN PRI TE to NT? This means from being configured as User Equipment (the PABX) to be Network Equipment (the Exchange). 2. How do you configure the card for E1 or T1? 3. In

Hi, Everybody, I can modprobe TDM400P card without feeding power supply , so what is the purpose of providing power supply in that card. Can any body tell me Regards Lokesh Portugal mail -lokeshkumar80@yahoo.co.in ____________________________________________________ Send a rakhi to your brother, buy gifts and win attractive prizes. Log on to http://in.promos.yahoo.com/rakhi/index.html

Has anyone else experienced a problem with the LED for span 1 on a TE410P or TE405P? I had a TE410P on which the span 1 LED would not light red, but once the span was connected, it did correctly light green. I RMAed the board to our UK distrbutor and received a replacement. However, the replacement board displayed the same problem! Wondering if it was related to the computer I was putting it

Thinking outside the box, four possible solutions come to mind: 1) use ssh (preferred for security), vnc, or xwindows to remotely access the machine (I've heard it is not good to use vnc and xwindows as the GUI tends to interfere with Asterisk timing) 2) in our server room, we have a keyboard and monitor on wheels and connect up to any server when it requires local servicing (or use a KVM to

Max TE410P card on an Asterisk Hello, Does anybody know the max number of TE410P/TE405P card we can put in an asterisk box? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/f220d3ae/attachment.htm

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040809/8f53bb6a/attachment.htm -------------- next part -------------- ? Hi There, We install asterisk in RH9. We've T1 line and four TE410P card. We wanted to configure this card. We used ztcfg to see the channel configuration. It shows like "Channels 0". How to configure

Hi to all out there using HP DL380 G4 servers, i found a way to get the Digium TE410P with older firmware running on a HP-Compaq DL380 G4 Server! Here's the step-by-step description: 1. download the latest BIOS (in my case it was 4.04 from date: 06/02/2005) for the HP-Compaq DL380 G4 using the "Systems ROMPaq Firmware Upgrade Diskette for HP ProLiant DL480 G4 (P51) Servers" Link:

I was once told by a lineman that the cables they use didn't have that many twists in them because it wasn't needed, and that the extra twists would effectively use more cable and thus cost and weigh more than triple what they do now. He told me that with the number of twists in the Cat 5 cable it would cancel out any interference, but he also stated that the effective length was

Hello i have two questions 1 - is there a maximum number of TE410P/P.C. (don't take the number of pc's pci slots in your account)? 2- if i installed two TE410P cards in the server, what should the server internet connection bandwidth be? . Regards Yousri -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All This mail is from a new comer to asterisk , just exploring I was going through the digium web site , In need some advice and suggestions , which card I should chose , should I choose TE411P (with on board echo cancellation ) or TE410P If I go for TE411P , I will be spending 1,000 $ more and for me finance part is critical , will I face

Was there any resolution on this I also have a TE410P in an box with an Intel E7501 chipset? -Vickers -------- Original Message -------- Subject: RE: [Asterisk-Users] Re: TE410P card in an HP-Compaq DL380 G4 server Date: Tue, 8 Feb 2005 11:13:24 +1030 From: Peter Childs <peter.childs@nec.com.au> Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion

I was wondering if there is anyone following the list that has this or similar PCI cards running in a 1U server. If so, could you possibly recommend a PCI card bus adapter? I'm not sure exactly which kind I'll need. I plan on researching the different types of adapters I can purchase for my specific mobo (Supermicro X9SCA-F), but I'd like to not waste time by ordering an incorrect

Greetings... I have a TE410P with four T1's going into it. Things look roughly like this: #1 Goes to PBX -- we're responsible for timing #2 E&M span to telco 1 #3 PRI span to telco 1 #4 PRI span to telco 2 If I set primary sync source to span 2, users report strange echo, distortion, and crosstalk problems, which sound remarkably like frame slippage on spans 3 and 4. If I set

I have a TE410P with two real Telco T1's and the other 2 ports terminate into an in-house voice mail/IVR system. Calls arrive from Telco are routed to the appropriate in-house system based on the DID Digits. This part works perfectly. Now I what to allow the in-house VMS to dial though asterisk to the Telco T1's. The VMS complains there is no dial tone on its T1 and drops the attempt.

I just got back from Boston where we completed testing of the TE410P for FCC, Euro, and Australian approvals, and I'm happy to say we passed all our approvals (including Q.921 and Q.931 layers, i.e. libpri as well as surges) for both telco and leased line applications. Hopefully we'll have the official documents soon, but I know there are a lot of you out there that are happy to hear

Hi List, While I was surfing the net last week, I found a link for "open source" pci telco cards. I'm not sure if it were isdn or analog related. The layout an all the stuff was free downloadable, so that you can build your own cards. Does anybody have the link? Yes, I know there is google, but i searched for over an hour, but can't find anything. maybe i use the wrong

Hi, > While I was surfing the net last week, > I found a link for "open source" pci telco cards. > I'm not sure if it were isdn or analog related. > The layout an all the stuff was free downloadable, so that > you can build your own cards. > Does anybody have the link? you're probably talking about the Zapata Telephony Project and their