similar to: Sounds cut out problem - HFC-S card, zaphfc, Xlite

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Hello all, I was playing with the zaphfc driver and i had these issues: I've tried to configure multiple spans (in TE mode, not NT) but it always give me errore "No such Device (6)"... I've 3 HFC-S based cards in the machine, but it seems to load only the first one. If i try to load only the first card, asterisk starts correctly, but if i try to place a call it gives the error

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hi, I solved the Problem: the context defined in zaptel.conf: context = zapincoming was not in extensions.conf, so nothing worked. ( I assumend this context is only necessary for calls from zaptel, not to it) This may be a bug: in the verbose log I found nothing like "[chan_zap] Could not initialize ..., due to ....", this had helped alot and had saved alot of hours (-;

Try commenting out the line pritrustusercid = yes Or set it to 'no'. That worked for me. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Jens Sent: Friday, January 21, 2005 7:18 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] zaphfc no callerid

I have a bunch of road warriors who I've set up with Xlite clients. Unfortunately the sound quality has been intermittent at best. Sometimes it's great other times completely unusable. When it's bad one usually hears harsh static when the other party speaks or their voice gets "clipped" to static if they speak too loudly. Many of these users have migrated to Skype ? much

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi! I just wanted to ask if anyone managed to get "ordinary" HFC-S ISDN cards with the zaphfc driver running in a Xen3 DomU. I am referring to this post ( http://lists.xensource.com/archives/html/xen-users/2007-04/msg00202.html ), which perfectly describes my problem and I am therefore going to simply copy-and-paste it here: ----------- snip ------------> Hi, I''m

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

Hi All, what is this? This happens after calling "make loadNT" And I can't do anything with this HFC Card, but the installscript from bri-stuff finished successfully! Aug 17 02:31:42 server kernel: zaphfc: freed one card. Aug 17 02:33:27 server kernel: PCI: Enabling device 00:12.0 (0000 -> 0003) Aug 17 02:33:27 server kernel: PCI: Found IRQ 10 for device 00:12.0 Aug 17 02:33:27

On Friday, March 31, 2006 3:52 PM Chris Earle wrote: > I'm wondering if I should be using zapHFC with my Junghanns card > instead of qozap? Why would you want to do that? Sorry if I missed the start of the problem but qozap is what you want to use with your Junghanns card (at least if you want to stay with zaptel/libpri). > Everyone always mentions zaphfc -- mostly I >

Hello List, is someone operating a DID /P2P / Anlagenanschluss with more than one HFC-Based ISDN-Card ??? I have now 12 hours of setup-troubles behind me with Colt-Telekom, where we did not get it working with two HFC-based cards. Here the setup: - 2 HFC-ISDN-Cards (the one from Conrad-Electronic) - bri-stuff.0.0.2 (with the asterisk-sources from the download.sh-skript) - two NTBAs from

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hello everybody, I'm having little trouble (well, pretty big trouble) with HFC-S card and Asterisk. My idea is to do VoIP/IAX link between two HW PBXen using two Asterisk PC boxen with ISDN cards in them. AFAIK HFC-S cards must be in NT mode for this installation, they must behave like state line for those HW PBXen. (if wrong, please correct me). Diagram follows:

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

It seems so simple, but I'm having no luck installing a HFC-s ISDN BRI card on *@home 0.5. I probably have to install BRI-stuff from Junghanns.net but that also downloads and installs another copy of * from Digium. I'm not sure if zaphfc has to be installed *before* Asterisk or if it's OK to do this afterwards. I've seen this question before, but: Anyone successfully installed a