similar to: sip.conf asterisk to vonage

I'm trying to connect my Asterisk server via sip using my vonage soft phone account. Has any anyone successfully got to work? I get error from asterisk saying: == Parsing '/etc/asterisk/sip.conf': == Parsing '/etc/asterisk/sip.conf': Found Aug 24 11:01:11 WARNING[1125329600]: acl.c:146 ast_get_ip: Unable to lookup '216.115.25.199:5061' when trying to register with

Does anyone currently use Vonage with Asterisk? I've tried to set it up but it looks like Asterisk (at least the version that I have) does not handle well the SIP call dialog, sending a BYE with the wrong tag. As a result, when I hang up, Vonage sends back a 400 Bad Request and the call on the PSTN side does not hang up. I know that Vonage does a lot of nasty stuff which impacts UA's

Hi All, I tried with different configurations and referred many articles to configure Asterisk with a Vonage account I have but all my attempts failed. I am a newbie and hope this mailing list will help fixing my problem and configure Asterisk. The error I get after I make a call to outside number like 18007633555 is -- Accepting AUTHENTICATED call from 59.93.69.218, requested format =

Hello everyone. I've seen postings for connecting asterisk to vonage but I'm still having trouble achieving that. I have a vonage softphone and I'm trying to register to vonage using asterisk. I have not had any luck. I am behind a firewall. I've successfully gotten xlite to connect and work from the same network. When I change the port setting in [general] to 5061, I am able to

Hi, I'm trying to get Asterisk to connect to Vonage (softphone acct) to allow me to place and receive calls. I have successfully configured Asterisk to route inbound calls and send them to the correct extension, but I can't get outbound calls to work. I have Asterisk successfully registering with Vonage, but when an INVITE is sent out, I get a "404 Not Found" back from Vonage

So Asterisk can't send VOIP calls to Vonage -- but it is still possible to use Vonage for flat-rate long distance by connecting the Vonage AT-196 to an * FXS port, right? The price is an extra D/A <--> A/D conversion. Jim Shilliday IT Director Equal Justice Center 1315 Walnut St. Suite 400 Philadelphia PA 19107 215-238-6970 -----Original Message----- From: Tim Petlock

I stand corrected! However you do get my point ... The bigger the company the worse it is. Having to deal with these guys is a nightmare. The company that brings me out in spots is Rogers Cable (24/7). They have this electronic air-head called "Gertrude" or something, (an android) who can't understand the word "NO" and has trouble with "YES" (actually like my

I just got setup with vonage.ca with the motorola ata unit.. I fired up ethreal and checked out what's flying over the network... The sniff below would lead me to believe that it might be possible to have asterisk spoof the User-Agent field and register itself? Any thoughts/feedback? Thanks. > > No. Time Source Destination Protocol Info >

Vonage doesn't sell just a softphone account -- or at least they didn't about six months ago when I was a Vonage customer. But they do allow a softphone as an add-on to an ATA-based account. Because the softphone account works with openly available soft clients, it also works with asterisk. The big "secret" is that they use port 5061, rather than port 5060. > > I

I setup a vonage account last year, and cancelled it last night when I put my asterisk box together and signed up for a Broadvoice account to use with it. Now I would like to use my Linksys router as an MTA, but realize it is still programmed with all of vonage's proprietary information and I do not know how to clear it. I understand that just pushing the reset button will not do it.

My previous post hasn't even made it to the list yet (am I being moderated?), but I got Vonage's Softphone service working for inbound and outbound calls. Keep in mind that there's currently no perceived limit on simultaneous inbound calls, which makes this a wonderful solution for Asterisk (at least for my use). Below is a sanitized snippet from my working sip.conf; your mileage may

Okay, my last post for the night. So, after tweaking my iptables rules I placed a test call from my * -> Vonage softphone account, to my Vonage main account (which uses the Motorola device). Once connected I tried punching a few DTMF's to check the quality and found I had been transferred to a fax machine. ???? Did I find a secret entrance to some fax machine at Vonage, or

I've been reading all I can in order to try to implement an asterisk setup. In speaking with someone the other day, they advised they thought there was a way to make a SIP or softphone (gnophone) go straight out to the vonage network through asterisk. I already have vonage set up with an ATA 186. What I'm wondering is is there some way that I could direct dial from a softphone

Is anyone using Vonage on an FXO port in Asterisk? How well does it work? Specifically, any echo/delay problems? Second part, I am assuming it is possible to separate fxo ports for least cost routing correct? In other words, I would like the routing to be such that any local or 1-800# dials fxo ports 1-4 which is a normal 4 line analog PSTN connection. Any long distance call will try to dial

I just installed Asterisk on my server and I have Vonage softphone. I need my Asterisk server to receive calls through the Vonage Softphone DID and make outgoing calls through the Vonage ATA using an X100p to connect to it. Can someone help me out on configuring this? I really need this for my business and would greatly appreciate the help.

Maybe somebody can help me. I'm testing my brand new [*], interconnecting it with several networks, but only via softphones up to now. I do have a VT1000 CPE from vonage, with a vonage line on the first FXS port, and would like to use the second FXS port to connect it to my [*] This is my question: My vonage VT1000 is connected between the cablemodem and a home gateway. Therefore, I

Hi All, I have installed Asterisk and able to create Users and get them connected to Asterisk after authentication. My question is how can I make calls to different DIAX clients through my Asterisk server. I also have vonage softphone account, using that I tried calling 18882255322 -- Registered 'manoj' (AUTHENTICATED) at 59.93.73.0:4569 -- Registered 'diax'

I am having trouble with this. I can dial 1800 numbers fine as well as FWD service numbers but not Vonage. I can be called from ipkall and fwd and can call aixtel numbers. I use aix2 with Fwd. My extensions.conf for Vonage: ; vonage numbers ; ; +2431 exten => _2431XXXXXXXXXX,1,SetCallerID,${FWDCIDNAME} exten =>

There was a flurry of "Vonage is going to unlock SIP" activity last year; did anything productive ever come of it? Are *you* using your Vonage lines directly into Asterisk? In lieu of that, for a 4 line small business that doesn't need to pay Vonage $150 a month, who? Broadvoice? Someone else? I'm a touch unimpressed with the fact that BV's website *won't quote you

http://advancedippipeline.com/60400413 "BOULDER, Colo. -- Leading Voice over IP service provider Vonage Holdings has complained to the Federal Communications Commission that competitors are blocking the use of its service, according to FCC chairman Michael Powell and others close to the company. "We're very actively on this case and we are taking it pretty seriously," said