similar to: HDLC Bad FCS (8) HDLC Abort on TE410P

On Wednesday 03 August 2005 17:33, Jens von B?low wrote: > Gavin, > > >> Any ideas/advice would be warmly received right now! > > You are not going to like my response... Erk :) > The only way I could get this to work (luckily I had 2 identical sites and > was busy with the upgrade to the gen2 card) was to downgrade to zaptel > 1.0.7. Alas no - just moved down to

Hi, We currently have an Asterisk box (P4 2.4 Ghz, 512Mb RAM, 1 T100P, Zhone Channel Bank and 1 E100P) connected to an ISDN running without any problems. That machine is working for about 1 year. Two days ago, we decided to switch that machine for two PowerEdge 600SC (HA) and we got some problems. The running machine (P4 2.4Ghz) has an Intel motherboard with four 32-bit 3.3v PCI slots,

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Hello, I get an Error every minute on the second card of two installed TE410P Cards in our System. The error is: PRI got event. HDLC Abort (6) on Primary D-channel of span 5(-8) PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 5(-8) Is it possible that there are known problems with 2 cards in one system? I'm running Asterisk/Libpri/zaptel from SVN branch-1.2-16008 I was

I have an * box connected to a Nortel SL100 through a PRI (US) using the Digium TE410P (quad-span T1 card). I don't have access to the SL100 - it is handled by another group. The span comes up OK (timing, framing fine). However, as soon as the D channel comes up, I get endless "HDLC Bad FCS" errors. I modified logger.conf to get rid of the messages (so I could see what else was

Hi Related to this message: http://lists.digium.com/pipermail/asterisk-users/2005-February/090205.html After having a lot of trouble with abort and breakdown of the PRI connection I finally figured out what was wrong: The kernel was compiled for generic ide chipsets which doesn't support DMA. When our daily backup created some load for the disks the interrupts for the digium card

On Wed, Aug 03, 2005 at 11:28:19AM -0500, asterisk-users-request@lists.digium.com wrote: > 10. Inter-Tel AXXESS failure: HDLC Bad FCS (8) on Primary > D-channel of span 1 (Gavin Hamill) > Date: Wed, 3 Aug 2005 15:32:48 +0100 > From: Gavin Hamill <gdh@laterooms.com> > Subject: [Asterisk-Users] Inter-Tel AXXESS failure: HDLC Bad FCS (8) > on Primary D-channel of span

Hi all, After running fine for a few months now asterisk seems to hang frequently , still functioning but the DAHDI channels seem busy (users report a busy signal when calling or being called) A reboot will allow it to run for another day or maybe 2 or 3 till the problem occurs again. running stock Asterisk 1.6.2.9-2+squeeze2 on Debian with stock kernel 2.6.32-5-686 i get the following

Yep, another list posting on this topic :) All the messages I've read on this are from people experiencing these errors in quiet times - I get them as soon as I plug a port on our TE410P to an Inter-Tel AXXESS PBX.. and I get them continuously... I'm just sticking an * box in between ISDN30e (we're in the UK so euroisdn) and the PBX.. and whilst the telco ISDN30e side works like

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the span. I have moved the PRI in question to the other server, and the problem does indeed move with the

hello my friends, when i make a genzaptelconf i get this message ******************** CAS signalling on span 2 conflicts with HDLC with FCS check on channel ******************* Any idea Please? I m installing zaptel 1.4 i checked in "http://bugs.digium.com/view.php?id=7860" that it's a bug but beacause i m a newbie in asterisk i can't undrestand what exactly mean Thank You

I'm running asterisk 1.0.3 and seeing occasional messages on the asterisk console that say: Dec 18 09:09:55 NOTICE[26411]: chan_zap.c:7381 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 or Dec 18 09:25:46 NOTICE[26411]: chan_zap.c:7381 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 They don't see to have a noticeable impact

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

hi all, i've now installed a TE410P (Quad T1/E1 Primary Card - Digium) and connected it to a primary line. My telco (eTel) only told me that they are using hdb3 and crc4. So i still don't know which coding i have to use (cas or ccs) - and what timing options i have to use. Have someone already get a card like this up in Austria with a line from eTel or from the telekom Austria ? Another

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

hi all, i am getting crazy with my TE410P - it won't work now we already think that the only thing which can be wrong is the cable. At our telecom endpoint we have 1-2 tx, 4-5 rx So - which cable do i need to get it working Already tried a cross over cable 1-2 -> 4-5 / 4-5 -> 1-2 (with this cable nothing works -> red alarm on both ends) Also a normal cable 1-2 -> 1-2 / 4-5 ->