similar to: Dial with no phone line connected

>> I have more FXO ports on TDM400's than I have PSTN lines available for >> testing. When all the lines were used up (the FXO ports are all in >> zap group 2), and I did a Dial(Zap/G2/${phone},5) it thinks the Dial >> succeeded even though there is neither line voltage nor dial tone. >> Can at least the lack of voltage be detected? It would be good in

Ahhh this could be my problem! I just checked which wires on the RJ11 cable had a voltage across them and it was the yellow and green (3 & 4?). From what someone posted the other day it's supposed to be Bumble Bee and Christmas Tree. I did have to get a technician out to fix my line when it was first installed because it was dead. Maybe he wired it up incorrectly or maybe they just do it

Ok... I am not a telephone guy... I was born after rotary phones, so forgive my ignorance in this matter. I am trying to get a really old rotary phone up and running with an ATA. Why? Who knows... just thought it would be cool. The problem is that it does not have an RJ11 connector, instead it has three wires (green,yellow,red). Does anyone know what that type of connector is called? Or

Hello - I have a TDM400P with 2 FXO and 2 FXS modules. Feeding the FXS modules are two VOIP lines which are terminated by VOIP adapters and have regular RJ11 wires connecting to the FXS ports. Since the two different VOIP lines have different phone numbers, and I know and can tell asterisk which VOIP line is connected to which FXS port, can I cause a distinctive ring on the extensions if a call

Hi, I have two small companies that are going to be sharing a * box. I have 2 TDM400's with 4 fxo ports each. Each company has its own sales person and they would like the sales people to always show their own caller id and have their own lines ring directly to their phones. Company 1 sales person uses the 1 port on the tdm400 and company 2 sales person uses the 2nd port of the tdm400.

The FXO lines on my TDM400 are connected to PSTN lines in Israel. As far as I know, the lines around here have disconnect supervision (I've seen some other Israelis on this list, anyone know for sure?), because it's worked on Dialogic cards, which reported hangup, not busy detect (while when I connect a Dialogic card to a PBX, I have to measure the busy signal's frequency/cadence or

Hi folks, Any Brits on the list got experience of hooking devices with standard BT plugs to the TDM400P? The TDM400P has the RJ11/RJ45 socket but I'm not sure if a standard adapter will do the trick or if we need to consider ring capacitors etc. Any links to buy the stuff would also be appreciated. Cheers, Simon -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

<div><BR>Hello,</div> <div>&nbsp;I bought a TDM400P, and intended to use it with my analog phone, which is RJ11 ofcourse. So, the question now, how do I plug in my RJ11 phone to the TDM400P card, which has an RJ45 interface? Also, since it's an 11B card, I also intend to bring in an analog line into the RJ45, so i am still left with the same question....how do I go

as my first project with *, i would like to replace our old neax2400(sds) with an * server. i've got an X100p and a TDM400 on hand already. for the CO lines, the X100p works ok with fxsks signaling though there are still strange things happening every now and again but more testing is on the way. my real big problem is the DID lines which our telcos call DDI lines; (incoming calls only) i

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

When I installed my first home-PBX three years ago, I was looking at "cellsockets" -- devices which will accept certain cellular phones and provide an RJ11 jack, generating the ring-voltage and recognizing DTMF, which in turn makes your cell-phone look like a CO line. Pretty cool stuff, in theory, but it just didn't seem to be worth the cost, especially since it locks you to a

Hi All, sorry if I post again this e-mail but I think the first one was lost. I don't know if this is OT but I'm working in my spare time at a small hardware project that match to what's requested below. It's a board with Input/Output capabilities and 10Mbps ethernet interface. It has Microchip software TCP/IP stack on it. Being at a very beginning stage, you can see a little

I'm going to be hooking FXS lines on a TDM400 to a PBX which doesn't drop line voltage at the end of a call, so I'm going to have to use busy detection. A few questions - The tones are taken from the tones specified by the zone in zaptel.conf, right? Which tones cause hangup? The PBX may not use the national standard tones. Does anyone have any suggestion for how I can

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I've got my developers kit from telappliant and got a machine up and running to become the house phone system. Most things are working now, such as incoming calls, call transfer, call parking, voicemail, etc. The one thing I can't do is make my analog phone ring! I can see the call coming in on the asterisk console and can then pick

When configuring a TE410P which is only attached to a single E1 together with a TDM400, how should one count the channels for the next Zap interface? Must I put 4 span lines in zapata.conf and define all channels up to 124? thus having the TDM400's start at 125? Or can I comment out the 3 spans I don't use and start at channel 32 for the TDM400? (this would get nasty when adding extra

Hi All; I am facing a problem that always the users confused and connect the telephone line coming from the telephone service provider to the FXS port and cause it to be damaged, specially if the card was 2 fxs and 2 fxo, so they make mistake and connect the line to fxs while it should be connected to fxo. What is the solution for this disaster? Regards Bilal

Today I had channel 1 on my TDM400 go to sleep, verified by pluggin in known good telco lines in various combinations on channel 1 through 4 - problem is channel 1, not anything external. So after seeing lots of stuff on the list re: TDM400's I power cycled, removed board and let linux say nothing's home, replaced board, told linux to ignore it etc. No OS/asterisk/etc changes made on

Anyone know of any equipment that I can use to connect a laptop running asterisk to a POTS line (RJ11) ? Regards, Dovid __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L