similar to: Make error installing bristuff-0.2.0-rc2b

I attempt to run make clean:make install and I get the following (cut short for brevity). zaptel.c: In function `zt_init': zaptel.c:6123: warning: implicit declaration of function `register_chrdev' zaptel.c:6124: `KERN_ERR' undeclared (first use in this function) zaptel.c:6124: parse error before string constant zaptel.c:6129: `KERN_INFO' undeclared (first use in this function)

Hello, Can someone help me. I got zaptel.0.9.1.tar.gz from ftp.asterisk.org, And then I uncomment the line with MODULES # ztdummy, run make clean, make, make install But errors happens as follows: ---------------------------------------------------------- make: zaptel.c:5937: storage size of `zt_fops' isn't known /usr/include/linux/proc_fs.h:193: warning: `create_proc_read_entry'

I'm a newbie with a TDM11B. I've read the FAQs about linking /usr/src/linux-2.6 to /usr/src/linux-2.6.8-1.521 and /lib/linux-2.6 to /lib/linux-2.6.8-1.521 but still get a million errors and eventual abort during compile. Could someone point me in the right direction? I do a yum update every day and I'm using the CVS from 9/14/04. I'm also using an ASUS CUSL2 system board.

I'm using Asterisk 1.0.2-BRIstuffed-0.2.0-RC2b - when anyone picks up a call with '*8' - the call will drop after about 20 or so seconds. Is this a general problem with Asterisk 1.0.2? As this is the latest release that it appears Klaus-Peter Junghanns has for public consumption - is there anything I can patch for just this problem - or has Klaus-Peter Junghanns (or anyone else) been

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

I installed bristuff0.20-RC3 (which includes * 1.0.3 stable) It works fine until I disconnect the phone jack for the ISDN line. Even after plug it back in asterisk still reports that it could not create a zap channel when I try to dial out and the line gives an engaged tone when I try to dial. Re-starting asterisk doesn't solve this, I have to stop asterisk, unload the modules, reload

Hi, it helps to have configured and working kernel sources installed. Configure your kernel sources for the running kernel and then run "make" in the kernel source dir to build the necessary scripts. You dont have to wait until the kernel is compiled. best regards Klaus -- Klaus-Peter Junghanns Am Samstag, den 25.06.2005, 02:45 +0200 schrieb Stefan Gofferje: > Hi folks, > >

Hi All, How to install bristuff on asterisk 1.2.14? install scripts are trying to download and compile those versions: asterisk-1.0.10 zaptel-1.0.10 libpri-1.0.9 and I'm running: asterisk-1.2.14 zaptel-1.2.12 libpri-1.2.4 I only need Pickup application from bristuff to be able to pickup channel independent calls e.g. when I have incoming call from PSTN and I would like to answer

Hello, I have about 10 Asterisk PBX in production with Bristuff-0.2.0-RC8q (asterisk 1.0.10) and I want to use Bristuff-0.3 now for the new PBX I am going to set up. With Bristuff-0.2.0-RC8q the ISDN lines are working fine, but the new version of Asterisk add some nice features. All these PBX are in France with France Telecom lines. When I use the new version after about an hour with

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

Is anybody familiar with the recent bristuff packages released ? There is only a 3 hour difference in release time between them and the CHANGES files are the same. Also what's strange RC7 has 163K and RC7a has only 87K. Ideas anyone ? Regards, Ivan

Hi, I have the SuSe9.2 installed in a box with a QuadBri. I have followed all the instructions i have found and this is my best result... only one error compiling zaptel :( .. y have the kernel sources an already made the links to its drwxr-xr-x 8 root root 328 Jun 16 20:20 . drwxr-xr-x 12 root root 320 Jun 16 14:05 .. drwxr-xr-x 3 root root 136 Jun 16 20:17 asterisk drwxr-xr-x 22 root

I applied the florz patch but my problems remain. Now I get all sorts of weird errors on the console and I cannot make outgoing calls. Incoming calls work as expected. I am using a single HFC-S card with BRI. Any clue what these errors below are? Ri = 44651 TEI msg = 3 TEI = 7f Ri = 3800 TEI msg = 3 TEI = 7f Ri = 42399 TEI msg = 3 TEI = 7f Ri = 42409 TEI msg = 3 TEI = 7f Ri = 22078 TEI msg = 3

I just received my dev kit and installed the hardware. I followed the directions Digium sends out to the letter and when I ran modprobe tor2 I got the following error: /lib/modules/2.4.18-19.7.x/misc/tor2.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

Hi all... I did some Google searches and didn't find any info on this so I'm posting it here... if this was recently discussed, I apologize for the duplication -- please point me to the appropriate thread. System Description: Supermicro SuperServer 5015M-MF w/ PDSMi Motherboard Intel Pentium 4 2.8 Ghz CPU 2 GB DDR2 Memory Digium T400P 4 Port T1 Card CentOS 5.1 (Final) Kernel:

I was dropping off junk at the waste transfer station and scarfed a UPS out of the pile of old TV's and VCR's. It was in good physical condition and as I expected, the battery was toast. A new RBC-2 battery restored it to working condition. Then I tried to get it to talk to some software. And I am having no luck. The unit is branded as a Nexxtech Model 6118507 650VA imported into