similar to: Australian STD "pips" & Telstra pstn

Is anyone having/had a problem with a TDM400P card hanging up on STD outbound calls as soon as the called party answers. I'm guessing that * is responding to the STD pips in some way. -- Howard. LANNet Computing Associates; Your Linux people <http://www.lannetlinux.com> ------------------------------------------ "When you just want a system that works, you choose Linux; when you

Hi folks, this is specifically directed to Australia Asterisk users...... We are having a roblem with x100p 's when dialing STD. Upon receipt of the approximately the 5th (out of the ten) PIP's asterisk will hang up.... Now I am wondering if others are suffering the same problem ?? Any ideas ?? (it might exist on other cards, but so far I have only noticed the problem on x100p's).

Hi Folks, Has anyone added timing pip capability for ZAP interfaces ?? What i need for an application is the ability to turn on pips to sound at various set times during a conversation. It's only required when a call is received via an interface card (PRI)(BRI)(PSTN) of being delivered to hardwired telephone handset. Any ideas ? Gary .

Do any of the Australian Telstra users have some working tx/rx gain settins for the Sangoma cards on Telstra that I can try, echo is acceptable but not perfect using 0/0. I will also post them onto the wiki. Regards, Andy

We just installed a box into a Melbourne site with a Sangoma A101U, it is running the latest Wanpipe drivers and has Asterisk on it that someone had compiled manually from source. This initially worked fine but for the sake of consitancy we removed the existing asterisk and used emerge to install it. During this time the box was off of the e1 for about 8 hours and when it was brought back

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

I am having problems getting incoming caller id to work on a Telstra Onramp 10. I have changed "/DEFAULT_CIDRINGS 2"/ Is there something i'm missing ? My Cisco 7960 just shows "asterisk" Thanks, Nathan [zapata.conf] context=incoming usecallingpres=yes relaxdtmf=no rxgain=0.0 txgain=0.0 busydetect=no pridialplan=local usecallerid=yes callerid=asreceived

Hi, now that these cards have approval in Australia, has anyone had any luck in connecting them to a Telstra Onramp 10 service? Are these configured as a PRI, bchan=1-10, dchan=16 in zaptel.conf and switchtype=euroisdn in zapata.conf? Better yet anyone have any of the above .conf files they could share? Is an onramp 10 what is referred to as a 'channel bank'? Craig

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

Hello list, I have an X100P clone card, and I've been trying to get it to receive Telstra Caller-ID without any luck. Hence these two questions:- 1) Will a genuine X100P work? 2) If so, where can I get one in Australia? Cheers, Jon

I've noticed that a few people here are from Australia. I'm wondering where you all get your hardware from. I'll probably order some of the X100P cards from Digium soon (and possibly some FXO cards), but for other things such as ATAs, etc. However - these obviously aren't ACA compliant. Does anybody know of compatible hardware (for POTS lines) that is ACA compliant? The cheapest

Telstra (Australian Telco) has recently introduced a feature to allow the sending of SMS direct to fixed analogue lines, with an appropriate handset. As best as I can figure out, this appears to use CID type signalling, or at least on a line that otherwise has no CID on it, CID is sent, but with a standard modem I can only receive the date, time, and phone number (eg normal CID info). After that

Dear All ~ I have * setup & running ok (with two Wildcard X100P's to PSTN). I also have two analog phones connected into same through a SIPURA 2000. These work fine, except that when I call out through PSTN & try to send DTMF tones to (say) a remote PBX to dial an extension, the gain seems to go wild (high), and the DTMF tones are not recognized at the other end. I tried setting the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Joseph, I've resolved this problem for myself by changind the order of lookups : $>cat /etc/nsswitch.conf group: pgsql files passwd: pgsql files .... but it'd be a good idea to compile add the ncsd (nis caching daemon). then the file will look like this group: cache files pgsql etc... as far as I looked at the code I think the problem

> > That would be called a milliwatt generator. It likely exists in their > central office, but its typically used by their technicians to ensure > new installations meet specs and sometimes in troubleshooting. Call your > telco repair number and see if they will give you the telephone number > for it. I'll try that. 1st line technical support at Telstra are not known for

Hi does anyone have a definitive list of countries other than those listed on the wiki which are supporting app_SMS on landlines using ETSI ES 201 912 ?? Thanks Tim Robinson Basingstoke, UK

Hi, I'm running Asterisk 1.0.8 on Gentoo, with an X100P (clone) card, and I'm having problems with Caller ID. I have run clidtest, and it seems happy enough, returning:- server clidtest # ./clidtest /dev/zap/1 Number: 0412222222, Name: MOBILE (that number's fake.) However, I'm not getting the caller ID passed through with *. Sometimes I get a "failed checksum" like

Hi there Has anyone out there embarked on credit card processing in a Rails app through Australian gateways such as eway? I''m aware of Payment and ActiveMerchant, but neither support Australian gateways. It''s a little beyond me right now to hack these to work with eway. Any clues would be appreciated here. Richard Sandilands

I have an x100p which suffers from echo (no surprise there apparantly :), and a few of the things I've read about tuning out echo say the first thing to get right is the tx and rx gain, and for that you need a few different types of test lines from the telco (Telstra, Optus, whatever). Does anyone have any numbers in Australia for such lines? I think they just need to send out a tone of a

List, With sites like this appearing everywhere: http://www.dontfilterme.com and http://nocleanfeed.com/ Just trying to get a general opinion with what everyone thinks of the filtering situation in Australia. Whether you believe its a good thing or a bad thing or you don't really care. I'm writing a letter to an Australian MP (Member of Parliament) and I want to get some actual opinions