similar to: Caller ID - TE405P - Telstra Onramp 10 - Australia

Hi, now that these cards have approval in Australia, has anyone had any luck in connecting them to a Telstra Onramp 10 service? Are these configured as a PRI, bchan=1-10, dchan=16 in zaptel.conf and switchtype=euroisdn in zapata.conf? Better yet anyone have any of the above .conf files they could share? Is an onramp 10 what is referred to as a 'channel bank'? Craig

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

Hi, I am currently trying to find a replacement for a dinosaur PBX and want to replace it with a VoIP solution. We have just moved our lines over to an Optus Multiline from a Telstra ISDN Onramp 30 service with 100 lines. My question for you good people is what sort of hardware do I need to interface Asterix into the Optus Multiline? The Optus service is terminated in my office to a SHDSL

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

Hello, We have 4 'Onramp-2' Telstra ISDN BRI services operating on Asterisk Server with Eicon 4BRI card. For most part the service is okay. However, we are are having problems with passing callerID to internal extensions. This is the set of command executed. exten => <pattern>,1,Answer ; Answer the line exten => <pattern>,2,NoOp(${DNIS}) ; debug statements exten =>

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

Hi, I have just put in a tdm400p with 4 fxo modules and am trying to dial out from x-lite to dial my mobile phone just to test. The output in the asterisk console is like this Executing Goto("SIP/2002-239b", "mobile|61400039953|1") in new stack -- Goto (mobile,61400039953,1) -- Executing Goto("SIP/2002-239b", "localcall|61400039953|1") in new

I've seen this question asked before but haven't seen a definative answer. Does the e100p work in australia? Did any one who was asking the question before bite the bullet and get one? I can get a te410 if i really have to but would prefer to stay with the cheaper option. Any comments appreciated, Thanks ------------------------------------------------- This mail sent through IMP:

Hello list, I have an X100P clone card, and I've been trying to get it to receive Telstra Caller-ID without any luck. Hence these two questions:- 1) Will a genuine X100P work? 2) If so, where can I get one in Australia? Cheers, Jon

Is there a way to have extensions automatically created for registered sip users ? I did some investigation and found some hope in chan_sip with relation to the somewhat undocumented usereqphone option but i may be totally off track. All i want to be able to do is send a call to number@ip_address where the number is the username configured on the phone that has registered with asterisk

Anyone have experience with the 3-08-2 release of Cisco's SIP firmware? Are there any new features in the SIPDefault.cnf? Thanks, Ron

We just installed a box into a Melbourne site with a Sangoma A101U, it is running the latest Wanpipe drivers and has Asterisk on it that someone had compiled manually from source. This initially worked fine but for the sake of consitancy we removed the existing asterisk and used emerge to install it. During this time the box was off of the e1 for about 8 hours and when it was brought back

Do any of the Australian Telstra users have some working tx/rx gain settins for the Sangoma cards on Telstra that I can try, echo is acceptable but not perfect using 0/0. I will also post them onto the wiki. Regards, Andy

Hi folks, just a quick update.... we managed to solve our problem by getting telstra to turn of the STD pips on outbound calls. We don't the effect yet on inbound (but we haven't had problems in the past) as most of our lines with x100p's are generally only used for outboung. Gary .

Well, Once upon a time, I had problems receiving callerid, and then one day, Mark was logged into my asterisk box helping with something else, and I asked him about this, and he showed me a nice tweak to some source file that made it work. Some time later, I must have done hundreds of CVS updates, and along the way, lost the above patch (one liner) and so callerID hasn't worked for a long

Telstra (Australian Telco) has recently introduced a feature to allow the sending of SMS direct to fixed analogue lines, with an appropriate handset. As best as I can figure out, this appears to use CID type signalling, or at least on a line that otherwise has no CID on it, CID is sent, but with a standard modem I can only receive the date, time, and phone number (eg normal CID info). After that

Is there a reason the variable ${DNIS} does not get set with incoming calls via chan_capi ? Is it related to the MSN=X in capi.conf ? version = chan_capi-cm-0.6.3 example; exten => _95555555XX,1,NoOp, ${EXTEN}, ${DNIS} == ISDN1: Incoming call '0400000000' -> '95555555' -- Executing SetCDRUserField("CAPI/ISDN1/955555 55-135", "Incoming") in new

Hi does anyone have a definitive list of countries other than those listed on the wiki which are supporting app_SMS on landlines using ETSI ES 201 912 ?? Thanks Tim Robinson Basingstoke, UK

I have the following configuration and am obviously missing something small that is causing * not to work as expected. I have the following defined in sip.conf [ccme-in] type=peer host=10.0.9.1 context=devel_in disallow=all allow=alaw nat=no canreinvite=yes qualify=yes and [devel_in] is defined in extentions.conf However when I try to call via the dial peer I have configured on the cisco

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595