similar to: wcfxs causing constant CPU spikes

I need to reopen this discussion because it's impossible to run spandsp (and VoIP) under these circumstances. With zaptel unloaded, I see the following "vmstat 1" output: no swapping, an occasional disk output, +/- 1003 interrupts/sec., less than 10 context switches/sec., CPU idle 100%. A very quiet system. I load modules zaptel and wcfxo, and the system utilization stays the

I have a brand-spanking new TDM31B (3 FXS, 1 FXO) and when I start wcfxs (the only module that recognizes the card) from Zaptel 0.9.1 I get: Zapata Telephony Interface Registered on major 196 Freshmaker version: 63 Freshmaker passed register test Module 0: Installed -- AUTO FXS Module 1: Installed -- AUTO FXS Module 2: Installed -- AUTO FXS

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

Hi, Has anyone in australia got asterisk running on FreeBSD? how would i pass the opermode=AUSTRALIA parameter to the wcfxs.ko module as kldload doesnt let you pass parameters to the module like modprobe in Linux. I tried to get the sysctl variable using sysctl -a it might use but nothing applicable was visible.... i need to set the impedences to 600 ohms, can someone please advice me on

I'm debugging a TxFax problem whereby the fax transmission fails. I suspect interrupt latency--some interrupt routine is holding its interrupt too long. I have all unnecessary services switched off and X is not running when I perform these tests. Some transmission are successful while others fail at random points. I've noticed that after I boot Linux, load zaptel, wcfxo, and wcfxs,

I am unable to compile the zaptel drivers on the latest kernel for fc 3, I get the following errors which are listed below if anyone has any suggestions on how I can solve this issue aside from trying a different distro, please don't hesitate to offer. Thanks in advance. [root@asterisk-test2 zaptel]# make linux26 make -C /lib/modules/`uname -r`/build SUBDIRS=/usr/src/zaptel modules make[1]:

<font size="2">Hello,<br> <br> I recently instaled an asterisk 1.0.3, libpri 1.0.1 and zaptel 1.0.3 withuot errors.<br> When i try to load the modules, i get,<br> modprobe zaptel -> load zaptel without errors.<br> modprobe wcfxs -> can't locate&nbsp; wcfxs<br> <br> I search for wcfxs location, and it is on

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

All, I have FC3 fedora core 3 and just installed and compiled 2.6.10. after rebooting I attempted to recompile zaptel-1.0.3. I did a make clean then make. I got the following errors. Any suggestions? ------------------------------- /usr/src/digium/zaptel-1.0.3/torisa.c:1139: warning: 'set_tor_base' defined but not used CC [M] /usr/src/digium/zaptel-1.0.3/wcusb.o CC [M]

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hi all I ahve been having problems loading the wcfss and wcfxo drivers I get an error message invalid argument and something about post install insmod failed the currently load modules do show the drivers loaded but asteris won't start lsmod root@slackware:~# lsmod Module Size Used by Not tainted soundcore 3332 0 (autoclean) wcfxo

Friday and Saturday I was wrestling with a VoIP system that was having very strange problems. It was playing the outgoing IVR audio at 2-5x faster than it should have been. I found that if I stopped asterisk, removed the wcfxs driver and installed the ztdummy driver, the audio would play fine. I tested this in and out several times and it always worked fine with ztdummy and never worked right

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no battery or anything), and if I try to rmmod & modprobe

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in /etc/asterisk/zapata.conf [channels]