similar to: Verizon PRI Setup Problems - Only Busy and Congestion

Hi - Thanks for the fast response! > Try changing your dial statment to use a group instead such as > Dial(Zap/g2/3055551212) Same result: Spawn extension (from-sip, 000, 1) exited non-zero on 'SIP/2000-8dca' -- Executing Dial("SIP/2000-a4f1", "Zap/g1/19142246402") in new stack Dec 14 22:11:09 NOTICE[1506]: app_dial.c:800 dial_exec: Unable to create

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi! I have a E1 PRI connected to my TE400P card on span 1, and two channelbanks on span 3 and 4 and * 1.2. Every few hours I get this message and asterisk dies just after that: Warning: No D-channels available! Using Primary on channel 16 anyway! When this happens restarting zaptel and asterisk services, generally puts the system back online my zaptel.con reads: span=1,1,0,ccs,hdb3

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I have just finished installing a new asterisk box at my work. The box is quite hefty, dual Zeon 2.8s with SCSI drives and 2Gb of memory. I have a 4 port Digium T1 card for channel bank and PRI access. I activated a PRI from a local CLEC (DMS-500 based, National protocol). This PRI is on slot 2 of the card and is set as the primary timing source. It is ESF/B8ZS. All the software is latest

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD

hi folks. i recently setup an Asterisk system in Hong Kong. their phone company told me that their T1 PRI switch type is Primary-NTT. however in chan_dahdi.conf there's no such option. i have it set to national. it worked fine for a while, but now suddenly stop working. in coming call just keep ringing and didn't even show up on console. out going call hang up immediately with cause code

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

SYNOPSIS Erratic red alarm T1 PRI on asterisk, but zttool running concurrently during alarm shows no errors, irq misses, or alarms, on any span. Using asterisk and quad Digium T405P, configured as follows: Span 1 connects to ISDN PRI (fractional 8 B channels, D channel 24). Span 2 connects to T1 Mux and analog stations. Span 3 connects to ISDN PRI Nortel BCM hybrid key system digital trunk.

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Hi all, I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs. Some users are complaining that they hear clicks and pops on the FXS lines, generally when they pick up the phone it's noisy. This happens only after a while, e.g. after a fresh restart of everything, all is fine but after some time these noises start appearing. From what I've read on the

I've been working with a telco for the past two days trying to get a PRI span up and running. This is a small-ish telco and I get the feeling they don't do this very often. Anyway, they specified a pretty standard setup: ni2 switchtype, esf framing, b8zs coding, etc. All of my b-channels are up, but we're having a heck of a time getting the d-channel to come up. He finds out that