similar to: voicemail playback problem

I got a Uniden UIP200 and started to configure it and I am lost.... I have a tftp server setup on my * server and have the files unidencom.txt and uniden<mac>.txt there. But it doesn't quite work yet. It registers as a sip phone (sip show peers), but I cann't dial it and the display shows #1 disconnected all the time. It has firmware version BS4.59a in it. I have no idea if I

Re-sent because had wrong subject line on first post, sorry. I have just installed * for a small office (P4 3Ghz, 1MB RAM, RH9). It's replacing an analog PBX, and for now, all incoming calls arrive on 10 FXO's. Outgoing calls are via Voicepulse. Phones are SIP, Cisco 7940G's. My problem is random disconnects on both incoming and outgoing calls. The phones are behind a firewall;

Anyone using the UIP200 with *? I am having difficulty getting the phone to register and *stay* registered for more than 4 seconds. The * console shows the UIP200 registering and records the user agent. The UIP200 displays station name and time on its LCD, then 4 seconds pass and it shows #1 DISCONNECTED. The * console reports no problem and believes the device to still be registered. A call

Hello We recently moved to Asterisk 1.2.4 (from 1.0.x) and our 10 Uniden UIP200 have stopped working ever since. We can make a call with the UIP200 to any other extensions, but it can not receive a call. In fact the UIP200 always appears offline: It does show up in asterisk a few seconds after the UIP200 reboot: -- Saved useragent "Uniden SIP Phone p2 Ver BS4.70" for peer uip200 but

I am trying to get a new Asterisk installation running using a Zultys ZIP2 phone and a Uniden 200 phone. I have the system working reasonably well (although probably not optimal) except for a couple of items. First, I can't get the voice mail message light to work on the Zultys phone but it works just fine on the Uniden phone. Second, the time presented on the Uniden UIP200 phone is 1 hour

Hi, We've recently deployed 6 Uniden UIP200 phones (running firmware 4.54). We've been having some serious problems: 1) All the phones randomly reboot themselves. Typically when trying to answer or initiate a call. 2) All the phones will disconnect from a calls with the PSTN after 2-3 minutes. 3) The phones are unable to interact with a remote IVR (digit presses are not received at

Hi, all. I've got my Uniden UIP200 configured via TFTP (had to get DHCP 3.0.1 -- Debian's latest is 2.0.x!), and all seems well... except for the minor detail that it doesn't work. It registers fine with Asterisk, but when I copied my Grandstream's sip.conf info and plugged in the Uniden stuff, no dice. Any ideas? Thanks... -Ken unidencom.txt: OverwriteLocalSettings

Hi, all. Got my Uniden UIP200 today (ordered from thetwistergroup.com), and was very excited to set it up... until I came to the realization that there were no docs with it whatsoever. There was, however, a sheet of paper with the stock warnings (don't use the phone in the tub, etc.), AND a URL -- for documentation. Score! Well, no. The URL it gave me, bcs.uniden.com, does indeed have

Hello all, Uncertain if I have a configuration problem or a buggy phone, I'm requesting that Uniden uip200 users attempt the following and share their results: - dial into voicemailmain - press 2 to change folders - listen to each of the folder prompts. Is the audio for the folder number clipped at the beginning? This audio clipping problem will also appear in other applications, such as

hello, yesterday the uniden uip200 phone was recommended to someone. i am looking for an alternative to grandstream bt-100 because i can not do a supervised tranfer with it. here my questions: 1) does the uip200 support supervised transfers? 2) can i buy the phones in europe, especially in germany? thanks in advance, jan goericke

Hi, I've read through the archives, and wanted to get an updated opinion on the Uniden UIP200 phone. Seems like there were a lot of opinions that it was a good phone, but there were a few items that people were waiting for firmware updates for, but that was in 2004. I'm going to be using them in an office, 12 phones, on a LAN connected to an asterisk box. Thanks for any advice or

Hi, I'm new to asterisk, and have a uniden UIP 200 that I got off of ebay. I'm having trouble getting the phone to register with asterisk. I've tried a few different settings. I'd be extremely grateful if someone with a similar setting could give me the sip.conf block for the UIP and the settings you're using in uniden.txt. Here's what I have currently: IP of phone

I just got my wife this phone, and when calls come in on the queue it will not ring, if I dial the ext it rings, here is the config from the tftp server: Thanks unidencom.txt # UIP200 Mass Configuration System Generic File # Notes: # 1. Lines start with '#' are comments # 2. To leave a field value unchanged (as saved on local phone), leave value to blank. # 3. To set a field's

Hi all, I'm experiencing a problem with SIP channels going ZOmBIE after the following sequence of events: - IAX2 client calls SIP client - SIP client consultive transfers (using sip REFER) the call to a MeetMe extension, and hangs up. At this point, the IAX2 client will indeed be in the meetme room, but a 'show channels' at the * CLI reveals that the SIP channels that were involved

Hello all, When it comes to echo cancellation, we have had great success using zapata.conf's echo cancellation. This eliminates the echo at the very beginning of phone calls. However, we now have a small office scenario where the users are hearing the introduction of echo several minutes into a phone conversation (where the first few minutes of the conversation sound fine): PSTN

I have several too and I also see this problem on occasion. Like you say, it is fairly rare and I can't pinpoint a cause or tell if it is a symptom of something else. I think I wrote to tech support about it but never heard anything. I'm wondering how long they will continue to support the phone. -Nate > -----Original Message----- > From: Jerry Geis

I have two asterisk machines. One of them has a Digium board (server A) and the other is simply using ztdummy (server B). Server A is running on Debian and Server B is running Gentoo. Server A is running Asterisk CVS-Nv1-0-7-06/01/05-01:27:25 and Server B is running Asterisk 1.0.7. The problem I have is that when I try to transfer a call into a meetme room in server B, it simply hangs

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

Hello Everyone, My company is about to deploy * as replacement for our existing commercial Altigen PBX. Meanwhile, I've been trying to find the best cost effective SIP VoIP phone which we can use in office for 20-30 employees, as well as a few remote staff. Normally I wouldn't post about a VoIP phone, however, this phone was released less than a week so I thought I'd give some

I just spent the last hour or so trying to get this firmware to work across a NAT with no success. I have a GS BT101 working through the same NAT, so I don't think it's the NAT itself. I have a STUN setup in * and pointed the UIP200 to it and I tryed several combinations of nat= in the sip.conf and in the config files for this phone. No luck(yes, I did a reload now with each change in