similar to: BRI Problem dialing out

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

Hi I've got an 8 port Junghanns ISDN BRI card with 4 ISDN lines connected to it; all 8 channels are configured in my zaptel.conf. I am having a problem where intermittently, but very often, the ISDN line is engaged when the user tries to make a call. It almost seems like the previous calls are not being disconnected once the user hangs up. I no there is a priresetinterval setting in the

I have a North American BRI configured as National ISDN (NI-1) on an SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's surprisingly inexpensive -- less than two POTS lines. I've been trying to find an inexpensive PCI interface solution to connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS lines because of the improved signalling, fast dialing,

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Dear asterisk users! I want to control a hardware pbx with asterisk. What I need to do this is being able to press "hold" which can be done with capicommand(hold) and then send digits on a bri card which connects to my asterisk computer. So far I use Dial(CAPI/ISDN1/27:<<digits>>/bo,15) to do this. Are there better ways? Note that these are not dtmf, I'm afraid. I use

I am going to try and use a passive AVM fritz BRI card for my * setup.. Here is the thing.. I need to order my BRI from BT.. The service that looks to be the one to use is what they call ISDN 2e becasue this has the option to setup hunt groups across multiple ISDN2e lines so I could add another line later to get 4 channels.. According to the BT website in order to use the hunt grouping across

I know almost nothing linux, and don't really know that much about Asterisk (proper).. but I was 'pulled' by this subject and grabbed an <mailto:Asterisk@home> Asterisk@home installation CD (version 1.3) and just went with it. Newbie doesn't quite describe it, I'm a banker.. this simply goes to show how easy Asterisk is becoming (I certainly hope this direction was meant

Hello all, I was wondering if anybody knows where one might obtain a PCI ISDN card supporting a single BRI for use with Asterisk in Australia (and using something like chan_capi). Because of the Isdn4Linux DTMF issue, I don't want one of those cards. I've already spent too much time messing about with my current card. I'm after something like the AVM Fritz! cards. I found one place

Hello Asterisk users, I would like to use 2 BRI lines on my * box but I haven't any PCI slot. Is it to possible to use 2 two AVM Fritz! USB. If not, what other solution can I use? Thanks Amaury

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi list, I am facing the following problem, i need to make the following scenerio work exten => _900.,1,Dial(Zap/g1/xxxxxxxxxx,25,r) exten => _900.,2,Wait(3) exten => _900.,3,SendDTMF(${EXTEN:1}) I am using PRI-ISDN with T400P card. Searching through archives, i found that we can add some 'w' s to the dial string. I tried that using on both PRI and Analogue channels but it

Hi All, Has anyone had experiences with Asterisk and ISDN Gateways or cards? I am looking to setup a home phone system using asterisk and am looking to convert my two existing no's to a single isdn2e line. I was wandering if anyone could recommend which is better to use with asterisk - ISDN Card or gateway? also which brands are best with linux/asterisk? I have used eicon BRI cards for

I am trying implement two-stage dialing. Scenario is following: 1. * Dials SIP agent 2. SIP agent answer the phone and provide dial tone 3. * Sends DTMF string 4. "Bridge" channel with calling party I thought that something like: exten => _2XX,2,Dial_but_not_connect_(SIP/BYEXTENSION,10) exten => _2XX,3,Wait,1 exten => _2XX,4,SendDTMF($DTMF_DIGITS) Should do it. Thank

I have a strange problem with overlap dialing. I installed an asterisk server between a Siemens HiCom PBX and our telephony provider. Everything is working fine except some strange problems with the dialing of the fax (connected to the HiCom PBX). It seems to me that if dialing takes too long Asterisk just hangs up the channel without recognizing that the fax machine is still dialing: (Fax gets

Hi all, I have an asterisk box set up with a bri card (using zaphfc). I have a bri cellular gateway connected to it beacuse I'd like to route all my cellular calls through that gateway. The probel I encounter is that when trying to dial a phone number, I've the message : unable to create a zap channel. My card is normally well configured because when connected to the NT, It works

Hello, folks! This is my first post here. I installed Asterisk from scratch and after reading a lot of information on voip-info and this mailing list I was able to get started. I can make sip-to-sip calls (just on a basic extentions structure, let's say for beginners) but now I'm trying to make this system works with my Teles ISDN BRI PCI card. I can make and receive calls through X-Ten