similar to: udev or not?

Forwarded back to the list so others might get the benefit of the answers, and I get fact checked by others. -------- Forwarded Message -------- > From: Lee <leeb00@gmail.com> > Reply-To: Lee <leeb00@gmail.com> > To: Steven Critchfield <critch@basesys.com> > Subject: Re: [Asterisk-Users] udev or not? > Date: Fri, 10 Dec 2004 13:00:29 -0800 > On Fri, 10 Dec 2004

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hi, I am sorry if this message has been reposted, but for some reason I am having problems with posting it. I configured asterisk and zaptel modules with fedora2. I want to be able to load the zaptel wcfxo and wcfxs modules. For now I will use only the Wildcard TDM400P card. I am able to load the modules but I cant configure them using ztcfg or zttool because the tools are compiled to use the

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address

Hello, I'm running Fedora Core 3 with udev, and asterisk/zaptel/libpri from cvs. I have followed the README.udev instructions replacing insmod with modprobe and rmmod with modprobe -r and adding the 60-zaptel.rules file, yet no matter what I do I still get this error on boot(or when I run service zaptel restart): [root@pbx ~]# /etc/init.d/zaptel restart Unloading zaptel hardware drivers:

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

I haven't seen anybody so far post a complex fix for the udev problems on FC3 with the latest kernel. On that note, I have a temporary fix to allow zaptel to load somewhat normally. I found that modifying the zaptel script to 1) load, unload, then load the driver modules and 2) insert a pause between modules seems to allow things to work. This assumes you have followed the instructions

This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W

Hello everybody, After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly. I run dual P3 500 Mhz box. After reading README.udev I put a file 60-zaptel.rules /etc/udev/rules.d # Section for zaptel device KERNEL="zapctl", NAME="zap/ctl" KERNEL="zaptimer",

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

You should see something like this.... (I have 8 channels) tuxpbx*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo incoming en 1 incoming en 2 incoming en 3 incoming en 4 incoming en 5 incoming en 6

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2) Then I'm told that the device doesn't exist. Please help

I have just got my X100p card and am trying to install it. I have built and installed the zaptel drivers without any apparent errors and I am now trying to get them working. I have the following in config files In /etc/zaptel.conf fxsks=1 In /etc/asterisk/zapata.conf signalling=fxs_ks context=default channel => 1 Now when I try ti modprobe the drivers this is what happens: Command: