similar to: Broadvoice outbound 404 error

I'm hoping someone can help me with a problem I've been having for a while now. I've googled and wiki'd to no avail. Whenever I place an outbound call from * to a PSTN through a SIP or IAX provider (e.g. Voicepulse or Broadvoice), the first 1/2 to 2 seconds of the remote call are clipped (muted). For example, if I call a remote voicemail system that usually answers with

> -----Original Message----- > service is compatible with Asterisk). However, I have a question: can > more than one person make/receive a call at the same using one VoIP > line? > > If five people in the office all need to use their phones at the same > time, would I need five VoIP lines, or would I only need one > VoIP line? > Am I over-thinking this? No,

I posted this question a while back, and I'm posting again in hopes that someone has some ideas. Sorry if you've already seen this. When dialing out using a SIP or IAX provider (Broadvoice, SimpleTelecom, VoicePulse Connect) I often find that after the call is answered the first few seconds of audio are cut off (i.e. I don't hear the called party). This usually results in the called

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

Hi all, I am trying to configure my Asterisk PBX to connect to a broadvoice account. I want incoming calls to go to the "s" extension and to ultimately have outbound calls routed through my broadvoice account(s). I cannot for the life of me get this to register correctly. I am currently receiving this message on the console: Failed to authenticate on Register to

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

Egad, not again with Broadvoice! Anyhow, I recently installed AAH and configured my TDM11B and got that and some SIP phones working. I still have some issues to work out, etc, but my current problem is Broadvoice. I have checked out all of the online resources, including the recent list exchange about the recent changes made by Broadvoice. However, the one thing I have found to be consitent in

Hi all, I've been trying to use BroadVoice as a SIP service provider. They don't officially support * but are helpful when it comes to answering questions for setup parameters. They claim they have no firewalls or access lists that need to be set up so I can get access to their servers. However, something's still not quite right when I use the parameters. It looks like our Asterisk

All, I have been fighting with my dialplan for hours now, and google searches talk lots but offer nothing in terms of explication for this. I have my SIP peer set up and working with Broadvoice: [sip.broadvoice.com] type=peer user=phone host=sip.broadvoice.com fromdomain=sip.broadvoice.com fromuser=5555551234 secret=password defaultuser=5555551234 insecure=port,invite context=broadvoice

Hello All, I'm just getting into *, and trying to use a Broadvoice account. It works inbound, but Outbound fails no matter what sip.conf parameters I try. From the recent posts here I think it could be: A bad CVS release - I will try to download and build from a new one Broadvoice not challenging and/or Asterisk not responding with an Authorization: in the INVITE header. I am

Hello, Have a weird problem when using asterisk (1.0.6). There are certain numbers I cannot dial when using asterisk with my broadvoice account. No problems with inbound. With outbound calls, I can call some numbers (for example broadvoice customer support number) and unsuccessfully with some. However, when I configure my account directly on x-lite, I dont see these outbound problems. Here is a

*sigh* Ok, I have fought and fought with this. I have read all the FAQ's, I have scanned the list archives. I can receive calls on * from my Broadvoice acct, but I cannot place calls... I have the 'World Unlimited' plan, and like 5 area codes that are local to me in Dallas. Can anyone help me? here are my config files... - sip.conf - [general] context=default ;

I'm getting a couple strange things with asterisk on Broadvoice. It works fine currently for inbound and outbound. Everything is registered, its perfect. My problems currently are: 1) After 20 minutes audio out to broadvoice goes away 2) After about 3 hours my registration attempts to broadvoice time out and the only solution is to switch to a different proxy which subsequently works.

I've setup Asterisk to work with Broadvoice for both incoming and outgoing calls. I can make outgoing calls, but when I try to receive an incoming call I see the following message on the console: [date] NOTICE[8661]: chan_sip.c:13178 handle_request_invite: Unable to create/find SIP channel for this INVITE It's registered with Broadvoice: Name/username Host Dyn

Hello All, I have 4 Broadvoice lines. If I call any of the lines it shows that is coming from the first line. exaple register=XXXXXXXXX1@sip.broadvoice.com:passwd:XXXXXXXXX1@sip.broadvoice.com register=XXXXXXXXX2@sip.broadvoice.com:passwd:XXXXXXXXX2@sip.broadvoice.com register=XXXXXXXXX3@sip.broadvoice.com:passwd:XXXXXXXXX3@sip.broadvoice.com

I have just installed * from the latest CVS and I can make calls via X-Lite to outside numbers but for only 30 to 35 Seconds at a time then Broadvoice will hang up on me but X-Lite will not know it. Once I hang up X-Lite then I will get the following error message: Spawn extension (default, Number-I-Dialed, 1) exited non-zero on 'SIP/200-6a22' -- Got SIP response 404 "Not Found"

I finally got my incoming and outgoing to work on Broadvoice with a configuration file that is no where close to the one given by them. Here it Is (sip.conf). For others who have a working config could u please share so that I could compare. Thank You [broadvoice] type=friend username=[number] fromuser=[number] secret=[password] host=sip.broadvoice.com fromdomain=sip.broadvoice.com

Hi all, a noob here, I am trying to get outbound calls through asterisk working with Broadvoice. I have consulted the following two online tutorials: http://www.broadvoice.com/support_install_asterisk.html http://www.voip-info.org/wiki/view/Asterisk+settings+Broadvoice in an effort to make outbound calls. My current settings are as follows: sip.conf register =>

Is the Broadvoice service up? I just signed up with them and started receiving calls in no time but could not make calls. And after a few minutes I cannot even place calls. register => [number]:[password]@sip.broadvoice.com [broadvoice] type=peer fromuser=[number] host=proxy.lax.broadvoice.com fromdomain=sip.broadvoice.com context=from-broadvoice dtmfmode=inband any help would be

So it was all working well and then suddenly I'm unable to get incoming calls from BV. Outgoing is fine. I'm using AAH. I have the following settings; register=9738281625@sip.broadvoice.com:PASSWORD-GOES-HERE:9738281625@sip.broadvoice.com/2208 [broadvoice] username=9738281625 user=phone type=peer secret=PASSWORD-GOES-HERE qualify=1000 port=5060 nat=yes insecure=very