similar to: CAPI Newbie

Displaying 20 results from an estimated 700 matches similar to: "CAPI Newbie"

2005 Jun 28
1
AVM CAPI INSTALLATION
I use AVM fritz card A1, I have install with instruction of Voip-info.or, but it don' work. capiinfo Number of Controllers : 1 Controller 1: Manufacturer: AVM GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-02 (49.18) Serial Number: 1000001 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation
2004 Dec 17
1
chan_capi - avm card does not work
Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info
2003 Jul 22
3
capi_chan error - CAPI not loaded.
Good day, *newbie alert* I try to run * with capi_chan (and later on SIP). System: Debian 3.0 / apt-getted most stuff except chan_capi and b1.t4 HW: AVM B1 ISA / Celeron 400 / 128MB RAM Starting * the following ends up in the messages Jul 22 19:47:03 WARNING[16384]: File chan_mgcp.c, Line 2925 (load_module): Unable to get our IP address, MGCP disabled Jul 22 19:47:03 WARNING[16384]: File
2007 Jul 30
2
Strange ISDN Troubles
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Ahoy I'm trying to setup Asterisk on debian etch (with the debian packages) with a "Fritz!Card PCI" ISDN card and chan_capi. Everything seems to be configured the right way (excerpts below), Asterisk seems to see the ISDN-card but if i try to place a test-call from the outside i don't see anything on the asterisk-console (set debug
2005 Oct 17
1
AVM B1
Hi, I'm trying to get Asterisk working with the AVM B1 card. I've tried every instruction set I can find, but to no avail. I think I'm getting mixed up as to what Zaptel/CAPI configuration to use. If someone is currently using one of these cards, would it be possible to mail me a few bits of the important config files? Sorry if I should have included something else too, but let me
2007 Nov 29
0
[Copfilter] Copy of quarantined email - *** SPAM *** [6.6/6.0] Problems getting Asterisk to detect call in
I have installed an Asterisk 1.4 on Suse93 using a FritzCard. Some calls are logged to the ISDN log, but Asterisk is not detecting incoming calls. I wonder whether some other device or process is preventing Asterisk from gaining access to the isdn line? Is there some way to ensure that only Asterisk can listening to the line, or get it to share the line with some other device, such as the fax
2007 Nov 26
3
Problems getting Asterisk to detect call in SUSE9.3, with FritzCard
I have installed an Asterisk 1.4 on Suse93 using a FritzCard. Some calls are logged to the ISDN log, but Asterisk is not detecting incoming calls. I wonder whether some other device or process is preventing Asterisk from gaining access to the isdn line? Is there some way to ensure that only Asterisk can listening to the line, or get it to share the line with some other device, such as the fax
2009 Apr 01
3
list substring
hi I ve a list of item x = ( "xxxxx1" "xxxxx2" "yyyyx3") I need to extract a new vector y = ( "xxxx", "xxxx", "yyyy" ) I mean, for each item I need to extract the first 4
2008 Jul 11
3
Linux equivalent of 'format' in solaris
It shows the physical disks on the server bash-2.05b# format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0t2d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248> /sbus at 3,0/SUNW,fas at 3,8800000/sd at 2,0 1. c0t3d0 <SUN18G cyl 7506 alt 2 hd 19 sec 248> /sbus at 3,0/SUNW,fas at 3,8800000/sd at 3,0 2. c0t4d0 <SUN18G cyl 7506 alt 2
2012 Nov 28
3
CentOS version for sparc
Hello there, I'd like to have iso image version for ultra sparc 64bit. Recently, I downloaded centos version 4.2 beta iso image and installed on SunUltra sparc 64 bit machine. It was hang when it went to the screen " the CentOS 4.2 beta screen, <Tab>/<Alt tab> | <Space> selects | <F12> next screen ". Any idea? Please help. Thanks in advance. Amy on your
2004 Dec 09
1
chan_capi question
Hi all, I've finally taken the plunge and had isdn installed. It's a BRI from Telewest in the UK. I'm told by the provider that it's in point to multipoint mode with 6 digit presentation. I'm using an AVM fritz (bt speedway) with the fcpci-suse9.1-3.11-02 driver. Chan_capi seems to be installed fine. I can receive incoming calls. However, I can't call out. When ever i
2005 Apr 13
1
Asyncronous Connection.
Hi folks, I need to develop asyncronous connection just like in DVB Satellite One Way Service, in my network. Incoming traffic and Outgoing traffic flowing through different link and interface. Here i describe you more, Existing system: [ Router A ] eth0 : 192.168.0.1 | | | | eth0 : 192.168.0.2 [ Router B ] Router A and Router B on the same
2005 Jun 30
1
Re: Hot swap CPU -- "build" is not a good CPU benchmark
From: Chris Mauritz <chrism at imntv.com> > <snipped> > Oy....I'm terribly sorry. Moderator, please delete my previous > message. It was supposed to be a private message to Peter. Bryan, > please accept my apology. It wasn't my intention to riducule you in > public. honest injun.... > <blush> > Must drink less coffee.... No apology required,
2016 Aug 17
20
[PATCH 00/15] Fix issue with KOBJ_ADD uevent versus disk attributes
This is an attempt to fix the issue that some disks' sysfs attributes are not ready at the time its KOBJ_ADD event is sent. The symptom is during device hotplug, udev may fail to find certain attributes, such as serial or wwn, of the disk. As a result the /dev/disk/by-id entries are not created. The cause is device_add_disk emits the uevent before returning, and the callers have to create
2016 Aug 17
20
[PATCH 00/15] Fix issue with KOBJ_ADD uevent versus disk attributes
This is an attempt to fix the issue that some disks' sysfs attributes are not ready at the time its KOBJ_ADD event is sent. The symptom is during device hotplug, udev may fail to find certain attributes, such as serial or wwn, of the disk. As a result the /dev/disk/by-id entries are not created. The cause is device_add_disk emits the uevent before returning, and the callers have to create
2004 Jul 14
2
Chan_Capi 0.3.4a error
I just downloaded chan_capi.0.3.4a.tar.gz but it will not compile on my system (Suse 9.1). I compiled and installed Asterisk and it is running, did I miss a configuration or dependency for Chan_Capi somewhere ? cheers, Mike linux:/usr/src/chan_capi-0.3.4a # make gcc -pipe -Wall -Wmissing-prototypes -Wmissing-declarations -g -I/usr/include -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DCAPI_ES
2005 Jun 30
2
[OT] SPARC platforms -- WAS: Hot swap CPU
Bryan J. Smith b.j.smith at ieee.org wrote: >Not only that, but people forget that SPARC is not sold by just Sun. >SPARC is an IEEE standard licensed under "fair and non-discriminatory" >terms. The SPARC ISA and most architectural details are freely >available. Yep - but what is your point with bringing that up? >The _majority_ of my Solaris/SPARC experience in more
2010 Jul 03
0
Hang ZFS due to asyncronous delete?
As most others have - I''ve been having issues with dedup. Here''s my situation, 4TB pool for daily backups of sql server - dedup enabled - so a typical directory has 100+ files that are mostly identical (some all are identical). If I do rm * OpenSolaris is dead, zfs hung, etc. sometimes it comes back after hours, sometimes I reboot (only if a directory I don''t care if
2006 Apr 07
0
Ajax.Updater asynchronous => false
I was just working on a project where I needed to use Ajax.Updater with a synchronous request. It appears like all one would need to do is set the asynchronous option to false. I tried this and noticed that the content was being requested synchronously but the content was never injected into the DOM tree like one would expect from Ajax.Updater. In order to get the content returned by
2006 Apr 08
0
Re: Rails-spinoffs] Ajax.Updater asynchronous => false
I just ran into this very problem myself. Yes, this is a bug in prototype. If you look in the code you will see that the relevent handlers and callbacks simply aren''t called with a synchronous request (onComplete is similarly not called). I submitted a patch <http://dev.rubyonrails.org/ticket/4657> over at dev.rubyonrails.org which fixes this behavior. If you decide to check it