similar to: more than 3 msns with chan_capi

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

All, before I start, I have read the readme and realise the dial syntax has changed since 3.5.....(and I really wish it hadn't).... anyway can somone please help me round a config issue? Previously I had a capi.caonf as follows. This config allowed me to have multiple MSN's on the same ISDN/Fritz! card under seperate contexts.

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hello asterisk-users, I recently set up an asterisk server using Debian Sarge. I also added an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed a new kernel (2.6.15.1) with modular support for the CAPI stuff and also integrated the FritzCard driver available from AVM. capiinfo succeeds in correctly showing the ISDN card. When talking from one PC to another via SIP, everything

Hi, how can I set up multiple ISDN controllers with chan_capi, so that every controller has its own configuration (MSNs to listen etc...) ? I know I can configure "controllers=1,2" in chan_capi's capi.conf but then the controllers have the identical configuration and context within asterisk. My setup: I have 2 BRI-controllers (in one AVM C2). 1. BRI: point-to-point, Number:

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hello, I am trying to configure asterisk 1.0.7pre to get incoming calls from an ISDN line using an AVM fritz PCI 2.0 with Chan_capi 0.3.5. My problem is that the context is not recognised in the /etc/asterisk/capi.conf I have in /etc/asterisk/capi.conf 's section "[interfaces]" the following directive context=isdn and the following directive in /etc/asterisk/extensions.conf in

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

asterisk-users-request@lists.digium.com is believed to have said: > >Hey Dan!! > >Give us a clue as to what hardware/setup & network provider you have there, >and we might be able to help :) > >Paul > Hello Paul, hello everybody! I have, too, an inbound call problem. I am using an ISDN Fritz Card PCI 2.00, together with chan_capi 3.5.x . As I call my number I get

Hi chan_capi users, this thing is awesome, no delays like in modem_i4l! Plus, it got those nice ISDN features. Here's my question: Does my service provider (Deutsche Telekom) have to provide me with these Services (CD, ECT)? (the Readme in 0.2.5 says "does not relay on service CD") I know, that I don't have CFU,CFNR,CFBS (which I would have to order seperately). How likely

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi there, I searched in mailinglist and in web, but no answer to my problem... Only this post with no answers: http://lists.digium.com/pipermail/asterisk-users/2004-March/038994.html I'm using CVS Asterisk (05/17/04) with chan_capi 0.3.1. (multiple controller support). In my Asterisk-box there are 2 Fritzcards (module for second card compiled with changes on sourcecode found in the web).

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP