similar to: Newbie Time

Displaying 20 results from an estimated 20000 matches similar to: "Newbie Time"

2003 Aug 31
4
Newbie - setup help
Hi, I'm trying to setup Asterisk on a Linux (redhat 8) machine. There are no analogue phones to be used & use is purely for internet traffic (SIPs). I've followed the setup guide from : http://www.automated.it/guidetoasterisk.htm But cannot get asterisk to run. If I type asterisk at the command prompt I get invalid instruction If I type ./asterisk start I get [FAILED] Can
2004 Dec 06
1
Another "Unable to create channel of type 'Zap' (cause 0)" error
.. and from a newbie no less :-) I have configured my BT101, and hooked it up to my * box. All is well. I have entered the following in externsions.conf, and this bit works: exten => 613,1,Answer exten => 613,2,Playback(demo-echotest) exten => 613,3,Echo exten => 613,4,Hangup If I pick up the BT101, and dial 613, sure enough I get the echo test.. All good. I have a TDM400 Card
2008 Jul 15
2
Incoming calls on zaptel not answered.
After an upgrade from asterisk 1.2.13 to 1.2.25 including upgrading libpri, zaptel, the incoming calls to a TDM400P REV I, with 3 FXO modules stop working. The board is working, I tested in another server with the 1.2.13 asterisk version. When a call is incoming, I do a ztmonitor to check the rx and tx values, but nothing appears on screen. Also changed the pci slot where the board is. The
2004 Dec 02
1
Blank Machine Again.
After a bit of looking around, I realise that my initial descision to go for Fedora Core 3 may have been a bit premature, (I read that some experienced users are having issues with this version) so I'm starting again. I just tried Xorcom Rapid, but it looks bloody complicated, and fairly stripped back. Which is the simplest (and most supported / used) distro / asterisk version to use from
2009 Oct 24
2
SVN newbie - No trunk/ in http://svn.asterisk.org/svn/libpri/
Hello, I'm rather new to svn, so please, forgive me if this question sounds naive but is it normal that no trunk/ subdirectory is visible in http://svn.asterisk.org/svn/libpri/ ? I can see a trunk/ subdirectory in either asterisk, dahdi-linux or dahdi-tools. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:
2006 Jan 21
3
cvs asterisk compile failed (newer libpri)
I used: cvs checkout zaptel libpri asterisk asterisk-addons asterisk-sounds iaxyprov astcc and in the same order I try to compile it. Asterisk ends with the lines below. It complains of a newer libpri, but I just did it a step before! What do I miss? chan_zap.c:62:2: #error "You need newer libpri" chan_zap.c:128: error: parse error before '<<' token chan_zap.c:133:1:
2009 Apr 02
2
cant get a x100p works
I have an ubuntu 8.10 machine. Linux 2.6.27-14-generic i want to configure a x100p card an use it with asterisk, so i download, compile and install: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 i try almost everything i found on the net but without success: if i run lspci: 04:06.0 Communication controller: Motorola Wildcard X100P when i run dahdi_hardware appears this:
2005 Sep 26
1
Re: Ring requested on channel already in use
I posted this 1.2.0-beta1 success story to asterisk-dev, and someone recommended that asterisk-users might benefit from it as well. Thanks, Alan Ferrency pair Networks, Inc. alan@pair.com ---------- Forwarded message ---------- Date: Thu, 22 Sep 2005 17:35:08 -0400 (EDT) Subject: [Asterisk-Dev] Re: Ring requested on channel already in use To: asterisk-dev@lists.digium.com > alan wrote:
2007 Jan 27
1
Via EPIA channel_find_locked: Avoided initial deadlock
In asterisk 1.2 branch SVN 51363 zaptel svn 1980 libpri svn 393 addons svn 332 My equipment is a Via EPIA minit-itx CN10000 1.2ghz, 1gb ram and a tdm400p (4fxo). A call comes from zap, a SIP ulaw receives the call, talks for a while and when SIP users tries to park the call, then dozens of... WARNING[3853]: channel.c:781 channel_find_locked: Avoided initial deadlock for '0x91bb840', 10
2007 Jan 29
1
detecting avaya busy tone
n asterisk 1.2 branch SVN 51363 zaptel svn 1980 libpri svn 393 addons svn 332 Asterisk is connected via tdm400p to an avaya system to reach PSTN. When a pstn phone hangs-up asterisk seems unable to detect the busy tone and i keep hearing like 20 busy tones until the zap channel get closed. I'm using loopstart to connect the fxo to the avaya. Some suggestions for busydetection? Thanks, --
2005 Mar 02
1
Getting Polycom IP500 to talk to Asterisk - um... Newbie question :)
> Hmmm... I have this aweful feeling that I'm choosing the > exact wrong time to ask a "newbie question" :) Oh well, here > it goes. > > The quick question is : "How do I dial an extension?" > (answer is probably - "you don't" in which case:) "How do I > dial my asterisk box?" - I have no outside line, I just want >
2005 Feb 27
2
[Asterisk-Dev] Asterisk 1.0.6
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Greetings Everyone! Version 1.0.6 of Asterisk, zaptel, libpri, and Asterisk-addons has been released. There is also a new tarball for Asterisk-sounds. They are available for download on the digium FTP site: ftp://ftp.asterisk.org/pub/asterisk/ ftp://ftp.asterisk.org/pub/zaptel/ ftp://ftp.asterisk.org/pub/libpri/ ChangeLogs are available with the
2004 Jan 30
1
Help!!!: test Asterisk error: error on IAX1.conf and warning on chan_iax2.c
Hi, all Please help me. My platform is RedHat Linux 9.0. I have a wildcard x100p. I just installed asterisk by following step: # cd ../zaptel # make clean ; make install # cd ../libpri # make clean ; make install # cd ../asterisk # make clean ; make install # make samples When I test Asterisk typing # asterisk –vvvvc I get one error and one warning: [chan_iax.so] => (Inter Asterisk
2005 Mar 02
3
/dev/zap not created
I installed asterisk on Fedora Core 2 kernel 2.6.5. I followed the standard procedure. zaptel-libpri-asterisk. The thing is that I constantly get the error message: line 4: Unable to open master device '/dev/zap/ctl' where the file zaptel.conf contains only 4 files: fxoks=1 fxsks=4 defaultzone=us loadzone=us I cant run asterisk and get a load of error messages. When I tried to check
2004 Oct 07
3
CVS branch v1-0 .vs v1-0-1
Which CVS branch is the correct official Asterisk -STABLE? cvs up -r v1-0-1 asterisk zaptel libpri asterisk-sounds asterisk-addons OR cvs up -r v1-0 asterisk zaptel libpri asterisk-sounds asterisk-addons -------------- next part -------------- A non-text attachment was scrubbed... Name: eric.vcf Type: text/x-vcard Size: 146 bytes Desc: not available Url :
2006 Nov 14
2
Problem with FXS ports of TDM400P
I just received two TDM400P cards, but I'm having problems with them. The full info is at: http://pastebin.com/824079 Extra, I'm using : libpri-1.2.3 zaptel-1.2.10 On a x86 stable Gentoo box. Kernel: 2.6.17 gcc-4.1.1, glibc-2.4-r4 Is that an hardware problem? Should I try the other card? -- Gustavo Felisberto (HumpBack) Web: http://dev.gentoo.org/~humpback Blog:
2007 Feb 14
6
genzaptool from "xorcom"
hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????
2008 Mar 28
2
New Tutorial: Asterisk on EPIA VIA C3
Hello list, after spending the best part of an afternoon trying to build Asterisk on an old EPIA VIA C3, I thought that writing a tutorial would make life easier for future compilers: http://astrecipes.net/index.php?n=356 I had never compiled Asterisk for a different architecture, and I'm pretty disappointed at how complex it is - building Zaptel, Libpri and Asterisk requires
2009 Jul 18
3
perhaps libpri issue (thought it was a dahdi issue )
I am current running on a production system zaptel 1.4.12.1 libxpri 1.4.1 asterisk 1.4.25 The above configuration works. I tried to update to dahdi 2.2.0, libpri 1.4.7 and asterisk 1.4.25 This did not work. calls came in but not out. I dropped back to the initial configuration. Today, I dried only updating libpri on the original configuration. I removed /usr/lib/libpri* installed libpri 1.4.7,
2011 Jun 14
3
sig_pri.c:985 pri_find_dchan: Span 1: No D-channels available! Using Primary channel as D-channel anyway!
Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file