Displaying 20 results from an estimated 8000 matches similar to: "chan_capi on 2.6 - impossible?"
2004 Sep 27
3
chan_capi, Eicon Diva server BRI, kernel 2.6?
Hi list,
Does chan_capi work with kernel 2.6? The Eicon Diva server card loads
fine judging from /var/log/messages but Asterisk gives an error when
trying to load the chan_capi module. I'm using chan_capi-0.3.5,
zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with
kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a
msg that may be related and don't know
2005 Mar 25
1
Eicon DIVA PCI ISDN cards (not server) work withasterisk!
Hello Marc,
Could you post the install details for the Diva PCI? I have a Diva Pro
PCI 3.0 and I am looking to get it working... I am running Debian
Testing. So far it appears there are a few things floating around but I
am not certain which direction to go. I know I need to load the firmware
first. I did manage to load the modules ok.
Thanks,
Greg
-----Original Message-----
From:
2005 Mar 23
1
Eicon DIVA PCI ISDN cards (not server) work with asterisk!
I just wanted to let you know that it's possible to use Eicon DIVA PCI
2.01 ISDN cards (not "server" divas) with asterisk.
First thing to do is to load the module. If you have two of these cards,
you should do it like that:
modprobe -v hisax protocol=2,2 type=11,11
And now you can have up to 4 incoming calls with two cards (try calling
yourself and see if anything gets into
2005 Mar 17
3
Compilation problem chan_capi and Eicon Diva 4Bri
Hi *,
I want to integrate the Eicon Diva 4Bri Card to Asterisk.
Eicon drivers and capi is installed. I use the latest dev version from
eicon compiled and installed for my fedora 2 system.
I found the chan_capi for asterisk from www.junghanns.net. Also loaded
the patch and applied to the chan_capi source tree.
I changed the Makefile to include the capi20.h from eicon:
2006 Jun 29
4
Very bad quality with AVM Fritz!card PCI and chan_capi
Hi everyone,
I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite
happy with it. However, I am experiencing a quality issue with my AVM
Fritz!card PCI which is used with chan_capi. When somebody calls me on
this line he hears a lot of noise and I hear "scratches" and "plops". It
is very annoying. Below is is my /etc/asterisk/capi.conf
I've tried to
2006 Feb 28
2
chan_capi and Eicon Diva
I am trying to use chan_capi with an Eicon Diva Server BRI.
I installed the Eicon drivers from source including CAPU and
I can use the board correcly using tty_test and minicom over /dev/ttyds01
or /dev/ttyds01.
I need to insmod capi ( why? it is not written anywhere) and then
capiinfo shows me all board parameters, but I have to break it otherwise
capiinfo doesn't exit at all, but I don't
2003 Nov 09
1
chan_capi & Eicon Diva problem
Hello,
I have an issue getting the chan_capi module to load in asterisk cvs
from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva
Server Bri card.
I load the modules with: modprobe -v divas divacapi
I load the firmware with: divactrl load -c 1 -f ETSI -vd6
Output in /var/log/messages is:
Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table
(http://www.melware.net)
Nov 9
2005 Jun 28
1
problems with chan_capi 0.3.5 , divactrl, eicon diva server, and kernel 2.6.10/2.6.12
Hello all,
I'm having problems getting chan_capi 0.3.5 to work well with an Eicon
Diva Server card using using the driver from linux kernel both 2.6.10
and 2.6.12 (vanilla versions).
I have a (really two) producci?n system(s) running chan_capi in another
identical Eicon Card using kernel 2.4.27 and the Diva Server drivers
from Eicon. I installed an compiled the source level rpm
2005 Feb 03
3
Where are chan_capi bug reports and bugfixes sent?
Hello all
I found a bug in the chan_capi driver (really a not implemented message
handling and then a false error condition) and I guess I have wrote a
patch to fix it (basically I searched the internet for other capi open
source implementation an borrowed the code snippet) but I don't know
where to send the report and bugfix.
I also found some miss-behaviours that I would like to share
2004 Nov 28
1
multiple EICON Diva 2.01 PCI ISDN cards with Asterisk - possible?
Hello,
I'm thinking of deploying Asterisk.
I already have a handful of EICON Diva 2.01 PCI ISDN cards.
I was thinking if it's possible to insert 4 such cards to my PC-Asterisk
server (which I yet have to install) and use them as 4 lines in case
anyone has to call me in / I have to call out using ISDN line(s)?
Any reply appreciated.
Tomek
2007 Jan 25
1
Failing to compile chan_capi
I've got a brand new Eicon Diva Server BRI card and I want to configure
it with Asterisk. I managed to get asterisk and zaptel to compile and
install, I've compiled and installed the drivers for the Diva card and
now I need to compile and install the chan_driver for chan_capi.
Unfortunately this fails miserably. I get the following messages:
I'm using: Kernel 2.6.16.37.4,
2005 Jun 16
9
chan_capi-cm-0.5 release announcement
Hi all,
I would like to announce the first release of the chan_capi
channel driver on sourceforge.net
The package is available for download with name
chan_capi-cm-0.5
and is the current CVS HEAD.
It is derived from the chan_capi-0.4.0PRE1 of kapejod.
The main changes are:
- complete rework
- fix race-conditions
- fix call state handling
- rework of debug/verbose messages
- added capiFax
2005 Sep 28
2
chan_capi-cm, Euro ISDN bus: 2 extensions on same BRI port not working
Hello,
I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with
chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As
a BRI connection has 2 channels and allows 2 simultaneous calls,
numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system
is working (partly, read on), the trick is the correct cable wiring and
setup the PBX's port
2004 Feb 17
5
chan_capi problem
Hi to all
I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus.
I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start:
[chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group
Feb
2006 Jan 16
1
chan_capi-cm and DID
Hi all,
i have asterisk 1.0.9 with an Eicon Diva 4bri and
chan_capi-cm-0.6. I have 2 NTBAs (one with did and one
without).
When using the one without did, i am able to place
outgoing and incoming calls. When i use the NTBAs with
did i have a layer 2 error.
Anyone an idea?
-- Executing Dial("SIP/2004-9634",
"CAPI/g1/43XXXXXX") in new stack
> data = g1/43XXXXXX
2006 Nov 21
3
Diva Server, chan_capi and tone detection
Hi all,
I have a Diva Server V-BRI-2 card, which support, as written in reference
guide:
Extended tone processing (human talker detection, generation and detection
of country-specific tones)
I would like to detect human speech and fax tone with asterisk. I think that
the diva card transmit a DTMF code when detecting voice, but chan_capi
doesn't receive this DTMF code. I verbose it
2007 Apr 19
1
Improve voice quality on Asterisk + chan_capi + DIVA BRI
Hello everyone!
I've got a Eicon Diva Server BRI card into my "*" box working just fine,
but I wander if there's anything I can do to improve voice quality for
my operators. I'm thinking something along the lines of "auto gain" and
sudden noise suppression (like when you hit a fax machine or the other
party accidently touches the dial pad on the phone).
Does
2006 Feb 21
1
Setting up an EICON CARD with CAPI
Hi everybody.
I'm trying to setting up a V4 BRI EICON card on ASTERISK 1.0.7
My linux is a debian.
It was working during a few days an suddenly (after a lot of reboot)
I've got this error message that seems to be very popular but I couldn't
find any
answer on the net :
==============================================.
Asterisk Dynamic Loader Starting:
== Parsing
2006 Feb 01
1
RE: Euro-ISDN
asterisk-users-request@lists.digium.com is believed to have said:
>chan_capi does not set the NT-mode. Your cards driver need to do that.
>E.g. for Eicon DIVA Server cards, you just set the '-x' option with divactrl
>or set NT-mode in the config wizard.
>chan_capi does not (need) to know anything about what protocol the card is
>doing. CAPI is independent here.
Ok.
2014 Aug 07
1
Dahdi > CAPI migration
Hello Folks,
I looking to migrate a pbx from one server to another. The original server has this ISDN card:
?
00:00.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)
?
The new server:
00:00.0 I2O: Digital Equipment Corporation StrongARM DC21285 (rev 04) << AVM ISDN Controller C4
Now I'm not fully aware of both's cards functions since the manuals