similar to: I just got my TDM22B - but no data sheet

Hi, I am using asterisk 1.4 with Digium TDM22B card. My system is running well except CALLERID. I have tried all options for cidsignalling, cidstart but no luck. Btw, I am living in Malaysia. From google web site, I found some one having the same problem with new version of asterisk but not in old versions. I do not want to try the old versions of asterisk. I really appreciate if someone can

Im getting the following error when I try to start Asterisk WARNING[16384]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Nov 29 21:40:43 ERROR[16384]: chan_zap.c:6195 mkintf: Unable to open channel 1: No such device or address I'm using a TDM22B card. ============= # Zaptel Configuration File # loadzone=us defaultzone=us fxoks=1-2 fxsks=3-4 ==============

Hi All; If one of my FXS port damaged at TDM22B because we connected the Telephone Line cable to the FXS port while it should be connected to the FXO port, then can I order S110M FXS Module and fix it instead of the damaged FXS? (This if we assume my problem that really the FXS port damaged). Rregards Bilal

Hi list, I am trying to install a TDM22B in my * box. I am using a Pentium III with SuSE 9.2 (2.6.8-24-default) and * 1.0.7. I installed the TDM22B (no IRQ conflicts), recompiled zaptel, libpri and asterisk. I modified a file (can?t remember which one) to create my devices entrien in /dev/. I also tryied ?make config? but modules don?t load at startup. But this is not my problem; I

Is there a way to test if the motherboard is ready for a Digium card (PCI 2.2) ? I would like to know from a remote computer, where I have (root) access, if this computer is ready for a TDM22B. bye Ronald

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi, Having 3 dataframes with different row numbers, but equal column names (see below) I want to merge them by Var1 so I've tried: merge(j1,j2,j3,by="Var1") merge(j,j1,j2,by=names("Var1")) But always got the same message: Erro en fix.by(by.x, x) : 'by' must specify column(s) as numbers, names or logical What I'm doing wrong? Thanks, Antonio j1

Hi James/Chris, You guys have done this before, so I'm guessing you can help me understand what's going on. If my buildbot config is: jobs=2, nt_flags=['--cflag', '-mcpu=cortex-a15', '--use-perf', '--threads=1', '--build-threads=4'] It uses -j4 for build, -j2 for running the tests:

I'm looking to handle 3 PSTN lines with my Asterisk server. I have a Digium TDM22B and Sipura 3000. The Sipura works great, but the TDM22B seems to have terrible problems with my board---virtually all peripherals need to be disabled in BIOS, and then there is terrible noise, terrible silence and virtually no ability to use DTMF in IVRs. I really wish the TDM22B worked, because I much

Dear R users, I have a few hundred .csv files which I need to put together (full outer joins on a common variable) to do a factor analysis. Each file may contain anywhere from a few hundred to a few thousand rows. What would be the most efficient way to do this in R? Please include some sample code if applicable. Thank you, b.

Hi all, i have installed two digium cards on my asterisk box a TDM04B & TDM22B. The channels are configured as show below: Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) Channel 05: FXS Kewlstart (Default) (Slaves: 05) Channel 06:

First time installing Asterisk and I have a strange problem with my TDM400P(TDM22B) card. When I attempt to dial out the first digit seems to intermittently get dropped. For example, I will make a call to 18882467555 and the first time it will connect and then the next time it will tell me to dial a 1 before dialing a number outside my calling area. This happens for any of the calls that I try

After many days of headscratching, I finally have a TDM22B that passes the wctdm Freshmaker register test (fix: disable ACPI in BIOS). In the meantime, I had set up an SPA-3000, and had that routing my PSTN line to * quite nicely. When I move this line to an * FXO port, is works very irregularly. About 40% of the time, there is an ungodly blast of white noise in the voice stream that

I got this nice TDM22B with two green modules left and two modules right /var/log/messages shows: Nov 26 23:47:48 dns kernel: Zapata Telephony Interface Registered on major 196 Nov 27 00:37:53 dns kernel: Freshmaker version: 71 Nov 27 00:37:56 dns kernel: Freshmaker passed register test Nov 27 00:37:56 dns kernel: Module 0: Installed -- AUTO FXS/DPO Nov 27 00:37:56 dns kernel: Module 1: Installed

hello, is there a simple way to run multiple benchmarks in parallel without breaking the reporting scripts? currently there's an explicit -j1 in Makefile.programs - i guess with purpose. we're simulating our target architecture and parallel builds/runs on multicore machines would drastically decrease the required simulation time. cheers, - dietmar

Hi everyone, I'm trying to input an excel datasheet with city names and lat+longs, that has already been converted to a .csv file and make a map using R with my data. My datasheet is 30 cities, with their lat+long, temp, elevation. So far all I'm able to do is load the datasheet into R, I installed the map+ maptools packages so I can see a map of the US in R, but I don't know how I

I'm having problems with a TDM22B. The FXO modules work fine. Both FXS modules fail to initialized. The error messages I see when the module loads: Init Indirect Registers UNSUCCESSFULLY. Indirect Registers failed verification. I already RMA'ed a TDM22B because of this problem. Now that the replacement shows a similar issue, I want to see if anyone else can think of something to

On Mon, Sep 26, 2016 at 8:08 AM, Carsten Mattner <carstenmattner at gmail.com> wrote: > On Mon, Sep 26, 2016 at 4:25 PM, Teresa Johnson <tejohnson at google.com> > wrote: > > No worries, thanks for the update. Teresa > > 2048 wasn't enough. Bumped to 4096. Only 1300 ninja targets left. > > Once I've been successful with this, I might try building a

> Please give us a link to a datasheet for that device. Hello https://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-sip-phone-3905/data_sheet_c78-651588.html On Fri, Apr 12, 2019 at 3:58 PM Antony Stone <Antony.Stone at asterisk.open.source.it> wrote: > > On Friday 12 April 2019 at 14:42:57, Gokan Atmaca wrote: > > > Hello > > > >

The datasheet is available at http://download.intel.com/design/network/datashts/82599_datasheet.pdf See 'Table 9.7. VF PCIe Configuration Space' of the datasheet, the PCI Express Capability Structure of the VF of Intel 82599 10GbE Controller looks trivial, e.g., the PCI Express Capabilities Register is 0, so the Capability Version is 0 and pt_pcie_size_init() would fail. We should not