similar to: Can isdn data calls routed through 2 t100p's

Hi all. First thing: I want to thank you all for your help over the past month as I've been learning asterisk. This is one of the more helpful lists. Even when I ask questions that have answers in the wiki ( which I missed because I've been over studying ). Second thing is this: My office is scouting out VoIP solutions, and I have suggested an asterisk solution. We will be

Do they fall under FCC certification if they're built to the same specifications as the ones from Digium? If I build my own T100Ps from the schematics and board layouts that are available, are they legal to plug into the PSTN?

Group Can I have 2 wildcard T1 cards in the same box? I was thinking the first card would have channels 1-24 and the second card would have 25-48 Does this sound correct?

All, Thanks for taking time to read. I am wanting someone to tell me that I have a clue here and that the following proposed setup would (possibly) work. Currently existing are 4 pots lines with qty. 10 AT&T 954/854 phones. Would like to convert to asterisk and at the same time do a mild feature upgrade. Proposing to get: PIII 800MHz or better >=256MB RAM

If you have used * to support a pri as pri_net (as opposed to pri_cpe), either to talk to another * system or a PBX of some sort, I would be very interested in hearing about your experiences. Imparticular, I would like to know that it works before I invest in the extra hardware. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 284-5800 ext 115

I'm about to install a second T100P card in my asterisk system, and now I'm wondering how the system determines span-1 vs span-2. Does the position on the PCI bus determine this? TIA Mike

I am new to Asterisk (and phone systems for that matter) and was looking for guidance. My company is looking at installing a new phone system/PBX in our new location and I am trying to convince them to go with the Asterisk PBX. I see on http://www.asterisk.org/index.php?menu=features <http://www.asterisk.org/index.php?menu=features> what features are available but my biggest problem right

Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate

OK, I think I'm ready for the next step from the X100P. Splitting a T1 with a T100P and a channel bank/s ~ 50 extensions. I think the existing system uses NEC phones for ~34 extensions, I don't know the specific model yet of the phones or the channel bank. If the channel bank is not compatible with Asterisk/digium what brand should I be looking at to interface best with Asterisk and

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

Hi, I believe the issues raised by this message are the same as mine, more on a commercial sense than for self use, but mostly the same. I've seen posts where real-life installations are mentioned, but not a reference to how Asterisk is working on production (and productive) environments. Any experiences would be very welcome I believe, not only on pure technical, but wider, sense. Thanks

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

I'm trying to use ZapRAS to enable ppp connection through my E1. After the ZapRAS command is executed, all sound is crappy on all lines! The only solution is to reboot the machine (or halt it, and then power it on since Digium's hardware doesn't like reboots). Anyone know how this can happen?! I'm using * 1.0.6 on Dell PowerEdge 1850 which are told (too late though) not to work

Hi, I'm trying to get ZapRAS working but not getting very far.. Asterisk CLI shows: WARNING[3355]: app_zapras.c:173 run_ras: wait4 returned -1: No child processes and /var/log/messages shows: using the plugin option requires root privilege Can anyone shed any light on this and any fix? Googling the error doesn't find much.. I'm not sure what 'plugin' it is talking about,

Hello, I'm planning to convert my phone system to Asterisk, as I've outgrown my TalkSwitch system. I have a few questions for experienced * users, most of which can be answered yes/no. Current Setup: - Talkswitch 48NLS (4CO/8Ext) phone system. - One CO line, two Vonage lines, one Voicepulse line connected to phone system - A third Vonage line directly connected to a fax machine - A

Hello, Does anybody know of a place to get a half-height PCI slot bracket for the Digium T100P card? I have an application to fit them in 1U cases for small, deployable PBX's. The T100P itself is short enough to fit in a half-height slot but I need an appropriate mounting bracket to screw it into the case. Thanks, Mark Hagler

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 8351 bytes Desc: image001.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050601/65fd0455/attachment.gif