similar to: RE: Cisco and PRI

I'm stuck running a old copy of asterisk because something strange is going on in later versions of the CVS.. When I call in from a PSTN into my cisco 2610XM gateway which then routes the call to my asterisk box via sip.. Asterisk can no longer process DTMF tones generated by the calling party. This affects DISA, prompts and menus.. Has anyone else had this problem?? and use.. I DO have

Yes that is correct but most likely you wont't need/use every option in an Enterprise load. Also, an enterprise load will require more memory and flash; which which will increase the cost of a router. Kurt

I would think I could do this but for some reason I am stymied. I have a PRI from RCN connected to a cisco 3640 (in my day "cisco" is all lower case :-)). My config looks something like this on the cisco... --------------------------------------------------------- voice-card 3 dsp services dspfarm ! ip cef ! isdn switch-type primary-5ess ! controller T1 3/0 framing esf linecode

Cisco PRI card in a 7200 running lastest IOS --> SIP --> * Problem #1: SIP authenticates it under "general" and gives it the context from [general] not from [cisco.ip.address.here]. Here's the relevant party of sip.conf: [209.104.XX.YY] context=dids type=friend host=209.104.XX.YY ; IP address of Cisco gateway dtmfmode=rfc2833 disallow=all allow=ulaw [general] ...

Hi, I had previously posted about connecting an AS5300 to * via SIP/H323. I got it to work via SIP, but only 1 call at a time would work, and if a user from the * side hung up, the cisco would'nt catch the hangup. I an now trying to hook up to the cisco via E1, with a Sangoma A101 card in my * box. I would like it such that I call from * via E1/PRI to the cisco, and call out via R2 to

* --> SIP --> CISCO --> PRI --> PSTN The PSTN sees no callerid. *---> PRI[zaptel]--> PSTN Callerid is there... which makes me think it's the cisco, not the PRI/PSTN/telco. CISCO PRI--> * PRI [zaptel] Callerid IS there... which makes me shake my head in disbelief, because * can see clid from the cisco pri, but pstn doesn't... but when * sends info on that pri,

Hello, I am using a Cisco-2,811 router with PRI as a gateway between Asterisk and Nortel TX-1. I had problems with name transfer and with the help of Cisco support I've fixed it. Enclosed here are the definitions needed for it. BTW, Cisco's CCM is using MGCP thus the Q.sig is handled by CCM. Here I am using SIP so the router must decode/encode the Q.sig. The Nortel should be defined

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

Does anybody have callerid name coming in on a Cisco PRI via a Cisco gateway via SIP to *? I've seen a few people ask and a few people that say it should work, but I've never seen an actual working config. I do a debug on our Cisco gateway and I can see the callerid name, however none of the features that should send it via SIP seem to work. Cisco docs say to use the following:

Does anybody know if SetCallerPres works on calls via SIP through a Cisco gateway? We are trying to mark outbound calls as anonymous and we set it to prohib, but calls still show outbound callerid. We are SIP from * to the Cisco gateway and then PRI outbound. If we strip the callerid num, then the first number on the PRI gets added as teh callerid, so we can't do that. We need to make

Hi all, I realize this is OT. I just got a Cisco AS5300, and I need to configure it like such: Asterisk -----(H323/SIP)------> Cisco ----- (E1/PRI)------->Telco So calls originate from the Asterisk side (registered users on SIP or just ZAP phones), and they go out H323 or SIP to Cisco, where they go out PRI. I have the Asterisk side sorted :) (either H323 or SIP), I need help in the

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

Hi, I am experiencing one-way audio from: SIP Device ----> Asterisk -----> Cisco 7200 The Cisco 7200 has a VXE+ card that will allow you to do SIP. I can pass audio from SIP Device to Asterisk through the Cisco 7200 to the other end, but the Cisco 7200 does not return any audio back to the SIP Device or Asterisk, it seems. I have tried upgrading to 12.3T IOS version, but no

Hi, Trying to set up a SIP environment with Asterisk - T1/PRI on Cisco 2811 - PSTN (Teltone TSP). SIP call looks working and I am able to make call from SIP phones to PSTN analog phones. But I have troubles with the Call from PSTN to the SIP phones. I guess the problem is the dial plan. I am using four digits extensions (2301, 2302,..., 2xxx) on the Asterisk for the SIP phones and the full

Anyone see an issue on asterisk 1.2 that it will not accept the invite from a Cisco gateway. If I turn off voice service voip signaling forward unconditional then Asterisk accepts the call but without cname. Below is a trace. Any help is appreciated. Thanks John Bittner Simlab.net voippbx01*CLI> <-- SIP read from 216.86.35.24:63549: INVITE sip:9734333001 at 69.60.198.130:5060 SIP/2.0

Can anybody tell me if callerid name is supported running SIP between a Cisco PRI gateway (any flavor) and asterisk? We have number support working and I thought I read that name support was added somewhere in 12.3T, but I can't find that info any more. Thanks. Peder

Does anyone have a config they'd like to share w/ the above hardware doing termination for asterisk? I've got one coming in tomorrow along w/ some DSP's and would like to not have to create the config from scratch to start testing. W. Kevin Hunt

Hi guys. We have currently Asterisk CVS-v1-0-08/15/05-15:53:48 connected in SIP with a Cisco AS5300 (IOS 12.3). One PRI is connected to the Cisco gateway. The problem we have is that on incoming PSTN calls to the AS5300, relayed in SIP to Asterisk, the callerID name is not being transmitted. We received the callerID number but no name. I know we are receiving the name from the PRI in

Hello: Has anyone on this list had to configure hairpinning on a Cisco gateway running IOS 12.2 or 12.3 and using a PRI for connectivity to the PSTN? If so could you tell me how it is done? I'm told this is the source of my call transfer problems and yet I cannot find clear instructions for how the configuration is done. Thanks,Steve -- ISC Network Engineering The University of