similar to: Meetme conference across WAN

I have ztdummy installed: Module Size Used by ztdummy 3464 0 zaptel 218756 1 ztdummy crc_ccitt 2176 1 zaptel ohci_hcd 16388 0 floppy 49028 0 pcspkr 2180 0 piix 8580 0 [permanent] ehci_hcd 24456 0 uhci_hcd 26256 0 rtc

Hi to all. I'm trying to use meetme on asterisk 1.4.22.1. On a debian i've compiled (as i need h323 support) openh323_v1_18_0 pwlib_v1_10_0 dahdi-linux-2.1.0.3 dahdi-tools-2.1.0.2 asterisk-1.4.22.1 All works fine, dahdi status is: asterik:/data/programmi# /etc/init.d/dahdi status ### Span 1: DAHDI_DUMMY/1 "DAHDI_DUMMY/1 (source: RTC) 1" (MASTER) asterik:/data/programmi#

hi guys: recently I want to buinding a meeting confence on asterisk and use the meetme application. I have a ztdummy kernel afteri the lsmod commond: ztdummy 5768 0 zaptel 182660 28 zttranscode,ztdummy crc_ccitt 3008 1 zaptel I also configure the meetme.conf conf => 1000; my extensions.conf [default] exten =>

When I call meetme: exten => 1000,1,Answer exten => 1000,n,Meetme(|||d) Asterisk is complaing with: -- Executing Answer("IAX2/xxx.yyy.142.204:4569-2", "") in new stack -- Executing MeetMe("IAX2/xxx.yyy.142.204:4569-2", "|||d") in new stack -- Playing 'conf-getconfno' (language 'en') Warning, flexible rate not

I originally built my Asterisk server without installing the Zaptel package as it was going to be a purely SIP based system. However when I went to setup conferencing using meetme I found out that app_meetme is dependant on the ztdummy for timing. I have now installed the zaptel package and I believe the ztdummy module is loading ok [root@astro asterisk-1.4.0-beta2]# lsmod Module

Hello, I'm trying to set up a conference room. When I dial it's extension, I get an audible error saying "Not a valid conference room, please try again" followed by a disconnect. I've got debug sip peer 1001 (my X-Lite client) and I see this in the logs: (I'm pretty sure it has something to do with ztdummy, but I dunno... I have the port installed, but I

Hello System: Debian etch with kernel 2.6.18-4-686 or 2.6.18 custom. Asterisk Version: SVN-branch-1.4-r55483M Zaptel Version: SVN-branch-1.4-r2302 modules all ok in compilation time. And modules loaded: ztdummy 5928 0 rtc 13364 1 ztdummy zaptel 181540 1 ztdummy crc_ccitt 3200 1 zaptel In /dev/zap directory I have:

Hey folks, Using FreeBSD 5.2.1 and I've got the current zaptel driver installed from ports (0.8_1) and current ports asterisk (1.0.1). I've set options HZ=1000 in my kernel config, recompiled and rebooted and as far as I can tell, I've done everything right but when I try to use the conference, the audio is very delayed, choppy and segmented -- totally unusable. At the

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I previously had Asterisk 1.0.7 running on a Linux 2.4.x kernel with ztdummy. I was able to do things like meetme and music on hold. I recently installed Asterisk 1.0.9 on a different machine with a Linux 2.6.x kernel running ztdummy. I installed and configured everything the same way, but when I try to call into a conference room I get the error message stating, "that is not a valid

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hey folks, Using FreeBSD 5.2.1 and I've got the current zaptel driver installed from ports (0.8_1) and current ports asterisk (1.0.1). I've set options HZ=1000 in my kernel config, recompiled and rebooted and as far as I can tell, I've done everything right but when I try to use the conference, the audio is very delayed, choppy and segmented -- totally unusable. At the

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hello Everyone, I just got my Dev Kit TDM today... :D I installed the X100P ok (wcfxo); however, when I tried to 'modprobe wcfxs' for the TDM400P(TDM10B), I got this error message: /lib/modules/2.4.19/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters /lib/modules/2.4.19/misc/wcfxs.o:

Hi... Actually, I have to digium cards install on my server running asterisk. They are X101P and TDM400P. Right now, X101P is running perfectly, but the another card doesn't work. In fact, it is not reconized by the server. When I try to load wcfxs.o it shows me the following message: /lib/modules/2.4.18-14/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by

hi guys, i got a TDM400P FXS card an everything is fine except for this when i do modprobe wcfxs , the linux shows 2 TigerJet Network Inc Model 300 128k. i don't know why it is showing 2 of them. or is that what it is? ERROR: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 0 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 0 cshould be

I followed the Wiki instructions to get zaptel to work on Fedora core 2. It looked like everything went perfect including the loading of ztdummy. However, I am having meetme and MOH problems synonymous with ztdummy not loading. Take a look at my lsmod...Any ideas? (I am running stable Asterisk on a DL360 - Dual processor) Module Size Used by snd_pcm_oss 46201 0