similar to: T100p half-height PCI bracket

Hi all, I've seen a couple of posts recently from people who are doing something with Asterisk and a T100P and a Nortel PBX. However it's not clear exactly what they are doing. Does anyone know if it's possible to use a T100P or T400P as a DSX-1 interface to connect to a T1/PRI CO module in a Nortel PBX? We have a Nortel Norstar Modular ICS PBX and I'd like to plug its CO

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel bank: the voice is not

Hi Last week I installed Asterisk (release1) with digium t100p single span T1 (wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is currently the only user of the t1 line. All worked well for about a half a day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I consistently get multitudes of blue alarms on all b-channels followed by a loss of d-channel: Aug 31

In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

Hi, I'm seeing a problem when calling into my Asterisk server from a T100P with PRI signalling. I'm hoping someone has seen this as well, however, it's a little hard to explain. When I'm navigating through Asterisk on an inbound call from the PSTN, I'm getting a random 'noise' during the playback of sound files. The best way I can describe this noise, is imagining a

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

Hey everybody, I'm looking for some information that I'm not finding by searching the 2004 Asterisk archives. I'm currently playing with a Digium T100P card and 2 Grandstream phones, things are working well. I wanted to move on to linking our Definity G3R Rev 8.2 to the T100P. Everything that I've read so far shows that you need a TN464 to accomplish this. We have a TN767E

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

I'm about to install a second T100P card in my asterisk system, and now I'm wondering how the system determines span-1 vs span-2. Does the position on the PCI bus determine this? TIA Mike

Hi Folks, I have a T100P ordered from Digium in the past. Its working perfectly fine but I now need to more the server to India (out-sourcing) and we will be getting an E1 line there. Does anyone know if T100P was capable (upgradeable) or swappable so that I could use it with the E1 lines instead? Any pointers to driver/firmware update would be highly appreciated. Thanks. R -------------- next

Does anyone have the physical spec sheet for the T100P from Digium? The one on the website doesn't have what I need. Things like 3.3 or 5v operation, uses n IRQ channels, requires 32-bit PCI, must be installed while standing on one foot and reciting the GPL, etc. Also, if anyone is selling a used T100P or TE4xxP I'd like to talk... Thanks, --Ernest

anyone have a recommendation for a place I can buy cheap motherboards that supports those 64-bit 3.3 volt PCI slots for the T100P ? I can't find them at Fry's or anywhere locally. All I can find online is dual processor server boards that are overkill for this application. I would like to use a P3/ P4/ AMD single processor. No Xeons or dual processor junk. Anyone know why digium

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Due to some failed hardware on another platform, I've had to move a T100P card to a different chassis. After this move was completed, I am seeing some strange results on the T100P card that do not display to me any failure mode with which I am familiar. The card comes up, and shows "good" carrier and status, but Asterisk refuses to bring the D-channel up. Calls of course do