similar to: Issue with the channel drivers

I've googled / voip-info'd / searched until my eyes are blurry, but couldn't see the info I was looking for. I've turned here for help! Asterisk CVS head (9/7/04) Fedora Core 2 (updated to 2.6.6 kernel) DE405P (jumpers set to E1) I want to put asterisk in the middle of our current pbx (Meridian Option11) Currently the meridian has a 2MB pri EuroISDN card linked via a rj-45 into

Hi below are my configs: pstn(e1)--->asterisk (span1)----->legacy pbx(connected via span2)-----> legacy pbx analog extensions. my dial plan is like callers dial into asterisk(span1) , hear an IVR option and they are connected to the agents via the legacy pbx (which is in sync with asterisk on span2)....This works perfectly fine until about 200 calls or so...After that time when asterisk

Skipped content of type multipart/alternative

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi, How would one activate/deactivate hardware echo cancellation on the TE406 card? Can it be done per channel? I'm going to run TE406 in the following scenario: ISDN -> TE406 -> PABX I understand from Steve Underwood's site that echo cancellation is not good for faxes (and they do that themselves). So what I want to do and bypass echo cancellation for selected extensions before

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Hello, I'm about to install asterisk as the PBX at a location that my company has just moved into and I would like to get some comments and advice on the installation. I am new to * and don't want to make any big mistakes so I would love to hear whatever anyone has to say. Here is what I have so far Server: * 2.8Ghz P4 - 1G ram * T400P Tormenta II (is this as good as the

Does anyone know how to get any of these VOIP phones to allow me to do menu selections through asterisk, like when accessing voicemail and such. Thanks :P --

Has anyone ever heard of this so called Dynamic Impedance matching on the ADIT 600? I called their support and they've never heard of it. We are of course having echo problems are on the far end due to digital/analog conversion on the local end using a channel bank. We have purchased an ADIT 600 and yes the complaints are "far less" however we're still getting them. While I have

I have a two port TE205P Digium card. I have set everything up to create a native zap bridge between the two spans. Everything works perfectly except one thing. Our telco has a "password" that has to be entered as soon as a long distance call is made. So if I dial a long distance call from my meridian system, asterisk bridges the call between two channels, my telco picks up and gives

Firstly, the problem... Ever since I installed and setup asterisk, I have had various problems, initially it was echo caused by the ISDN (isdn4linux) card I was using. So, I upgraded to the X101P from digium. I still had echo, so I figured it was also caused by the ATA186 (cisco) I was using. So, I upgraded again to the TDM40B quad FXS card. This solved pretty much all my problems, except

Hi I have made myself a derivated menusystem based on the complex.c menu that cames with syslinux. And now I need to read a file, search for my pxebooted netcards mac address, and write some changes back to the same file. All the writing and reading I hopes will be of no trouble, but how can i find my own mac address? (and IP adress would be nice). I have searched the list, but I really cannot

I have no new information, just a note of encouragement to those traversing the bowels of h323: I've been trying to get h323 working with asterisk for several months now, trying with chan_h323 & chan_oh323 with all kinds of different combinations. As with several folk on the list, I've had no luck. Either I had no audio, or I could only receive calls, or I could dial but no had

Is there a soft phone for PocketPC or iPaq? If not, is someone working on it? I will be more than willing to contribute my mite if needed. Thanks, -- sudhir

Hi Thanx guys for the help on understanding howto read dmi info! I now have a custom boot menu for install of different linux versions based if they have been installed before (reinstall is ok for users, first install is not), and installquirks like if we detect odd hardware, we add install options to redhat installer so it can install anyhow (for instance hp dc7800 who needs pci=nommconf as

Hi, I have data like this.... print(x) ID VAL1 VAL2 1 B A 2 P Q 3 T S What I would like is data like this... ID VAL1 VAL2 1 A B 2 P Q 3 S T So that VAL1 and VAL2 are alphabetically ordered. Any advice is welcome! San. [[alternative HTML version deleted]]

Hi, I have created a heatmap using heatmap.2 having 7 clusters. I would like to extract the list of genes that are in these 7 clusters. Is there any function that can be used to extract genes for each cluster? Cheers, Sudhir -- __________________________________________________________ SAVE PAPER - Please do not print this e-mail unless absolutely necessary Being happy doesn't mean

Hi all, I have a very good query related to printer sharing using samba. Following is the scenario... I had installed HP laserjet 9040Dn printer on redhat Enterprise linux 5. Shared it using samba. Used winbind protocol to integrate linux with windows AD 2003. Now i am able to see printer in Active directory as well as linux computer account in AD. But unable to set option lpadmin -p printer

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the