similar to: Cisco ATA-188 w/502 Error on CallWaiting

Hi, I have some problems transfering call from phone to phone with my Asterisk. When I dial Flash I can hear for half a second the dial tone, but it stops suddenly. The other phone hear the on hold music and pressing flash key another time I get back to the previous channel. On the asterisk consolle seems to be all ok, this is whant I can read: asterisk1*CLI> -- Swapping 0 for 1 on

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

I'm trying to use a 4 port ATA that was designed for use with MGCP 1.0 / NCS 1.0 -- is the channel_mgcp compat with NCS -- anything I can do to make it compat?? This is what happens - below *CLI> mgcp reload Reloading MGCP == Parsing '/etc/asterisk/mgcp.conf': Found Use EXIT or QUIT to exit the asterisk console == MGCP Listening on 10.1.22.39:2427 == Using TOS bits 0 mgcp

Hi, I tried to establish NCS call b/w 2 endpoints of same PacketCable MTA using asterisk-10.0.0. I observed that MDCX sent to aaln/1 contains its own SDP. Some I observed with aaln/2. So voice path is not established b/w aaln/1 and aaln/2. My Configurations: mgcp.cong: [mta84.globaledgesoft.com] host = mta84.globaledgesoft.com wcardep = aaln/* callwaiting = 1 ;canreinvite = 1 dtmfmode

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =

Hi all, I am configuring asterisk in a cable modem network, using a motorola TM401A. I can make calls from the MTA but I can receive, display the following error: -- Executing [1500 at alberti:1] Dial("OSS/dsp", "MGCP/aaln/1 at 0-13-11-82-bd-a.ssw.intercal.net|30") in new stack [Sep 2 00:10:53] NOTICE[28062]: chan_mgcp.c:3572 mgcp_request: Asked to get a channel of

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

I am setting up with meetme a conf with X number of asterisk boxes and "other" devices and phones. I am using the l parameter for all devices being listen only but I'm not sure thats happening as I am getting some feedback (some devices are close to each other like 5 feet). How do I ensure that a=recvonly is being set or sent when bringing a device into the meetme? Can I added

Hi All, When asterisk bridges a call between 2 peers and peer-A's user puts the call on hold, then peer-A sends a INVITE with recvonly in the SDP. Asterisk responds to peer-A with sendonly in the SDP and asterisk sends an INVITE to peer-B with recvonly in the SDP. Peer-B then responds with a sendonly in the SDP. I've noticed in the above scenario that peer-B contiutes to send audio to

Hi! I have strange problem, I hope it's just a configuration problem, but maybe not. I'm trying to make a call between a MGCP gateway and Cisco 5300 talking SIP. Everything is fine except that audio is one way (from 5300 to MGCP gateway only). It seems that during reinvite Cisco gets confused by session ID and version and excpects RTP stream on different port. The call flow on SDP

Hi, I'm fighting with HylaFAX, Asterisk and T38Modem since some time, to get fax2mail and mail2fax working, my SIP-provider only supports T38 and thus using G711 with IAXModem is not an option. I have got running mail2fax with HylaFAX+ 5.5.0, Asterisk 1.4.20 and T38Modem 2.0.0 successfull, but I'm not able to upgrade to anything newer than Asterisk 1.4.24. I was able to break down this

Hello all, I have a problem where problem with one way audio, and I think it's related to "a=sendonly" and a re-invite. Can anyone please assist? The scenario is as follows.... - We send an INVITE to a peer, and it replies with a "100 Trying", and then a "183 Session Progress" message containing "a=sendonly". - Asterisk plays the caller music on hold,

The Asterisk Development Team has announced the release of Asterisk 13.9.0. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/asterisk The release of Asterisk 13.9.0 resolves several issues reported by the community and would have not been possible without your participation. Thank you! The following are the issues resolved in this release: Bugs