similar to: 3com NBX intergration

Hi, I've looked pretty wide on Google for this so I don't think it's been asked before. Has anyone had experience integrating Asterisk with a 3COM NBX system? The only way that I can see that looks possible is via the 3Com NBX ConneXtions H.323 product and then one of the H.323 Asterisk channels. Has anyone done this? Any pointers as to what to avoid or whether to even attempt it?

Has there been any luck getting the 3Com NBX series phones to work with Asterisk? Thanks! -Andrew

Does anybody know if the 3com NBX 100 phones will work with Asterisk? The phones require a boot image to be sent either through layer2 or layer3 before they will function properly after being powered on each time. Thanks.

I sent this once already but it didnt show up in my mailbox so I am not sure if ever made it to the list. If it did, my apologies. I have an * system and an nbx. My plan is to use several grandstream 286s and plug the the phone cords into the NBX's analog FXO card. It works fine but after I make a call, the port stays open on the NBX and I cannot make another call for around five minutes

Has any advancement been made to get 3102 operational in either a SIP or H323 asterisk environment. A post back in time mentioned a downloader service. >From the posts and articles I have read, the NCP is acting like a bootp and tftp server which uploads the configuration to the phone?? Am I close? if so, where does one get the SIP image for he 3102 and 2102 phones? I had 8 donated, but they

Hello, everyone, I am currently trying to get the asterisk server to talk with a 3COM NBX with T1 connection. My asterisk server has a T100p, TDM20B, a couple of sip phones. Now the sip phones are calling 3COM NBX phones fine, however, the analog phone has problem when dialing the NBX phones. The connection is established and the NBX auto-attendant picks up the call however the NBX end says that

We've been talking about moving from our NBX100 to an asterisk solution for some time now. Well, to make a long story short, the call processor on our NBX has went south. We are now forced to purchase a new call processor >$500 or move our solution to asterisk. (Which is up and running and have been tested with Grandstream Adapters.) My question: Is there anyone out there that

Hi, I would like to simulate data with a binary outcome and a set of predictors that are correlated. I want to be able to fix the number of event (Y=1) vs. non-event (Y=0). Thus, I fix this and then simulate the predictors. I have 2 questions: 1. When the predictors are continuous, I can use mvrnorm(). However, if I have continuous, ordinal and binary predictors, I'm not sure how to simulate

i am just curious how many * systems are in the real world with more than one user. do you run a certain version? you dont update CVS do you? any admins running a system of over twenty? over fifty? over one-hundred? i deal with 3com and nec systems all day (i am cerified in the 3com nbx advanced network telephony, elite voice mail, CCNA, A+, nec ipk, and soon to be "asterisk school of

Dear all I am trying to calculate the value of n using uniroot. Here is the message I am having: <<< Error in uniroot(integ, lower = 0, upper = 1000, n) : 'interval' must be a vector of length 2 >>> Please would you be able to give me an indication on why I am having this error message. Many thanks EXAMPLE BELOW: ## t = statistics test from t -distribution

Dear my friends... I am still new in CentOS. I use CentOS 5 for my new server with cpanel. I have installed the cpanel. The steps were: 1. cd /tmp 2. wget http://layer1.cpanel.net/latest 3. sh latest The installation show a message that the cpanel installation was completed. But I can not see the cpanel login form on my server, either: "http://WWW.MYWEBSERVER.COM:2082" or:

Greetings all, I am interested in setting up a lab in my house to run my home phone system. Can some one point me in the right direction hardware wise for achieving this goal? I happen to have a few 3com NBX phones, and have been told that they are SIP compliant but am not exactly sure if I believe 3com...I would be interested to know if anyone has these things working on *. In any

Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an

Hello! Is there a phone compatibility list anywhere? I know Asterisk is supposed to be compatible with IP phones that support SIP, h.232, and IAX, but a list of phone known to be supported would be a nice addition to the documentation. I need a buisiness phone, and the Cisco is _EXPENSIVE_ I like the 3com 1102, but it is NBX phone, and I can find no documentation of this phone working

My new company is going to enter a bid competing with 3Com and Siemens solutions from others. Voice service is a PRI T-1 with a block of 100 DID numbers, a second T1 that will carry Integrated voice/data, 12 voice/768K for redundency. I asked this a week or two ago, now I have more details. Best/$ channel banks that work with Asterisk and Best deal on phones... 16 business, 34 basic IP

I love it... I buy a half a million dollars worth of Trashiba's finest ... I download Asterisk for free... I now refer to it as legacy 18 months and 300 extensions later! Anyway, I am trying to integrate my dial plans acrossed platforms. PSTN>>>CTX670>>>Asterisk The dialplan I would like to setup, 1xx,2xx,3xx,7xxx to the CTX 670 4xx,6xxx to a remote ctx100 (this is setup

All, Have already got Samba 3 and W2K Ad intergrating working in production without any problems. I have set up a test domain to test W2K3 and Samba3 on a Red Hat 8 server. I did the following: * Have set up the NTP Daemon to synchronize time with the W2K3 domain controller. * installed the latest Kerberos packages for Red Hat 8, maid sure that krb5-workstation is installed. * installed the

Greetings, We are looking at installing a VoIP system with Asterisk and are currently looking at the line of 3Com phones. Has anybody had success with using the following phones? We need to buy a lot and we don't want to end up with phones that don't work properly with asterisk. 3Com 3101 (model with speakerphone) 3Com 3102 Business Phone 3Com 3103 Manager Phone 3Com 3105

Because it's a new service without much traction and I need something now and also because this will be a fairly large project and as such I don't want to use a third party service to collect a 'fee'. Dean > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Dovid Bender > Sent:

Hello everyone. I humbly admit I need some direction. I have search newsgroups and the Samba help files, but I must be missing something or just not getting it. I am comfortable witrh Samba in a small workgroup environment, I feel like a fish out of water when trying to intergrate Samba into a W2K Domain/Active Directory environment. While I consider myself technical, I've never had to manage