similar to: Sipura 3000 FXO

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

Anybody using a Sipura 3000 for FXO with Asterisk? Mine is working except for one small nit... When a call comes in from the PSTN, the Sipura answers it and then passes it on to Asterisk, which plays extension ring tone. I'd prefer for the POTS line to stay on-hook while the extension rings, and to only be answered by the Sipura when the extension answers. Has anybody made this work?

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of

Hi list, Well I really didn't want to see things get to this point, but Sherman at Sipura along with their President Jan F. leave me no other choice. SIPURA has been provided a letter from our attorney for Breach of Contract and damages. They have yet to respond. A quick background. 1. Sherman (SIPURA's Director of Marketing), stated that we would do a join press release for the Oct

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

How can I dial *67 on a Sipura 3000 if I dial from a SIP phone connected on an asterisk server. I always get a message saying that authentication failed for INVITE for sip221@192.168.1.6. If I dial a number without doing *67 it's working fine... sip 221 being the extension of my Cisco phone and 192.168.1.6 being the IP of my asterisk server... I have my outgoing context configure

Anyone have experience with Sipura's? Anyone know if they offer a warranty? Would like opinions on these, good or flame. We bought *one* to test with and it died, can't even get a response from Sipura "support". Could anyone recommend another device to replace these? Prefer 1 or 2 port design. Ty :-)

Hello list, I have several SPA-2000's and 3000's scattered about the Internet (all behind NATs). Because I do not qualify as an ITSP, Sipura will not license their "Sipura Profile Compiler" so that I can have the units remote upgrade, remote re-configure, etc (via TFTP or HTTP). This is extremely annoying. Right now if I have to make a config change to any of these

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

I'm experiencing a very unusual problem with a few of my sipuras. They keep over heating after minimal usage. I unplug them and let them sit for 15 minutes and it starts working fine. The other way around is that I put a fan on it or something to keep it cooling. Has anyone else experienced this or are they just defective units? Regards, Mohammed Salim EZZI Telecom, Inc.

I need another Sipura 3K and the replacement I think is Linksys SPA3102. Any input on how reliable is it? -- #Joseph GPG KeyID: ED0E1FB7

I have a Sipura 3000, apparently configured correctly, when incoming calls arrive on the telco port they arrive properly on the Asterisk system - however they don't get routed properly. The Asterisk message: Dec 30 07:47:16 NOTICE[2745]: chan_sip.c:7486 handle_request: Failed to authenticate user WIRELESS CALLER <sip:714XXXXXXX@1.0.24.5>;tag=7f8072c0c46250f7o1 X's are there to

I am considering using Sipura-3000s as FXO devices for my * system. Has anyone tried them in that configuration? They interest me because they need no PCI slots and therefore no drivers. I would much prefer not to have any special kernel requirements for my system. /carmi

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

This question isn't entirely Asterisk related, but I'm hoping that someone here may have the knowledge to respond to me anyway. I'm using Asterisk with several Sipura SPA-2000 SIP devices as FXS adapters. I would like to have my SPA's automatically provisioned through http or tftp, but I can't find any information on how to do so. Sipura's tech-support has not been very