similar to: Re: [Asterisk-Dev] Use the Meetme application with another module thanUSB-UHCI

A better explanation can be found here... http://www.digium.com/index.php?menu=faq#TDM%20&%20Analog_0 > -----Original Message----- > From: Benjamin on Asterisk Mailing Lists > [mailto:benjk.on.asterisk.ml@gmail.com] > Sent: Monday, September 27, 2004 11:37 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] FXO question

I'm having a similar issue to this in that the USB ports on the system are ohci based, not uhci, therefore ztdummy will not work. My system is also running the SMP kernel so zaprtc will not work. To me it looks like the only good solution is a hardware timer, even if it's as simple as an x100p card. Kelly PS. If you read Jon's message again, the answer given is not acceptable for

Hi all, I'm configuring meetme in asterisk but no luck. I dont have a digium card, so based on the wiki, i have to install the zaptel driver and enable the ztdummy on it. I compiled, install the module and enable it on the module.conf. When i tried to start the asterisk, asterisk wont start because of the error in loading the meetme module. Jun 16 15:36:56 WARNING[-1084989312]:

Does anyone know where to disable rtc support on redhat 9.0 using make menuconfig? I thought I disabled it but still got the following error when trying to make zaprtc: zaprtc.c:109: storage size of `rtc_irq_timer' isn't known zaprtc.c:719: storage size of `rtc_fops' isn't known zaprtc.c:107: warning: `DECLARE_WAIT_QUEUE_HEAD' declared `static' but never defined make: ***

Kristian, I have 2 X100P cards but neither work on my Compaq DL360 G2. The system will not even boot! Take a look at my initial post and let me know if you have any other advice. Regardless, thanks for your post! ------------------------------------------------------------------------ - I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards

Any help would be appreciated as I am a novice trying to work around a difficult situation. This is what the zaprtc helpfile says: zaprtc, getting zaptel timing out of your realtime clock ======================================================== Make sure that you _dont_ have rtc support compiled into your kernel! INSTALL: make USE: make load REMOVE: make unload I interpreted this as

I'm running into a bit of a problem setting up conference calls. The box I rent at a colo doesn't seem to have USB hardware.... When I try to load usb-uhci I receive a "device does not exist" error. Which means I can't load ztdummy.... The system has a rtc clock module, so zaprtc won't work... (which I'm scared to unload rtc because I don't have physical access

I have a system with no Digium hardware in it (two others with 2 X100P cards in each of them as well). I'm interested in using MeetMe in the one without the hardware (it works great in the ones with the hardware). I can't use ztdummy, because the system has usb-ohci drivers, rather than usb-uhci. I have read the little there is about zaprtc, and I am wondering whether there is a

Hi, I know this question may have been asked before (although the archives don't seem to suggest it), but has anyone had any problems with Asterisk accepting a PIN number for a conference room. At this point in time I have established the conference definition in the meetme.conf file as well as specifying the appropriate lines in the extensions.conf file. meetme.conf file: conf =>

I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards but neither will work in my DL360G2. The system will not even boot with either card in the system. Other PCI cards seems to work fine. I called Digium support and was told that there must be a conflict between the card and my Compaq DL360G2. I then moved on to ztdummy. I'm sure the

Hi, I'm using a HFC card on my asterisk box. I tried to make a conference but it doesn't work. I read on internet to use ztdummy but my server has no uhci (only ohci but it doesn't work) so I cannot use it. I tried zaprtc but after loading the module (it appears when typing lsmod) nothing has changed. Should I buy a x100p to get the right timing? Or there is another solution? TIA

Hi, ztdummy says the following: VoiceBOX:/usr/src/zaptel# modprobe ztdummy /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_register /lib/modules/2.4.18/misc/ztdummy.o: insmod

Hi, I don't have a zaptel device for conferencing. I read from the lists, that ztdummy and zaprtc need to be installed to get conferencing. I could able to compile successfully with ztdummy and when i receive the call it says, -- Goto (13732,s,1) -- Executing MeetMe("SIP/-08118800", "1234") in new stack == Parsing

I am still stuck, anyone got any ideas ? Hi, Having no digium hardware in my box and two cpus and a ohci usb bus im forced to use zaprtc. I have recompiled the kernel and removed enhanced rtc support. When I attempt to compile zaprtc I get the following error. zaprtc.c:1077: warning: implicit declaration of function `barrier' zaprtc.c:1078: warning: implicit declaration of function

This is not directly * related, but could be. My company is using a VoIP conferencing solution that is suffering from developer neglect. I've considered trying to leverage *, and our internal developers can build the management interfaces. If that plan is not accepted by management, I need to find a commercial solution that works. Requirements: H.323 SIP G7.11/G7.29 Multiple unique

zaprtc 'load' is failing on my machine (the make was fine, same output as other posts to this list) [xxx@xxx zaptelrtc]# make load sync modprobe zaptel insmod ./zaprtc.o ./zaprtc.o: init_module: Input/output error Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or

Hi to everybody, seems that I cannot load the zaptel modules: ztdummy says the following: [root@Hayabusa misc]# modprobe ztdummy /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_register

I am trying to use meetme() on SIP channels. I found this line on voip-info.org ------------- It *is* necessary either to have a Digium card or a dummy timing driver (e.g. ztdummy or zaprtc) in order for MeetMe to work at all, but that doesn't help you use AGI with SIP channels: They have no capacity to use any AGI script at all. If they try to, they get no audio. ----------------- I am

I try to use meetme app after reading manual i compile and install zaptel with ztdummy when i make lsmod i have ztdummy 2532 0 (unused) wcusb 20064 0 (unused) zaptel 179168 4 [ztdummy wcusb] usb-uhci 26348 0 [ztdummy] usbcore 51616 0 [wcusb usb-uhci] after it i recompile asterisk and after it i have

Hello all, I really appreciate the replies I've gotten about this so far (especially the support for wanting to run it on Solaris!). The core issue seems to have been missed, though -- is there any way to run a complete Asterisk solution on Solaris 10 (including music-on-hold and conferencing)? This probably comes down to a few issues: - Is ztdummy (a component of Zaptel) *really*