similar to: sipura over heat

Hi everyone, I'm having an odd problem with one of my sipura boxes. The box registers the first time with asterisk properly after being plugged in. After which, some of the subsequent registration tries fail and the box becomes unregistered. However, after a few hours, it finally successfully re-registers and the cycle continues. I have not been able to figure out the problem but

I'll try to keep this short and sweet, I don't want to confuse you, or myself.. So here goes I had a DID, it went down, I got a new DID (800#) and I changed the exten=>###-###-#### to the new 800 number in extensions.conf I'd done lots of changes to the config files and nothing seems to be doing anything, When I dail the 800 number all I get is a fast busy signal. When I log into

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

Did anyone setup or configure more than one company using same * server? If so, can you give me a quick start up? HAK ATIL

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

Guys, For what it's worth, after months of trying to troubleshoot issues with them, and after paying them around $2500 for setup and a down payment (it's unclear what of that will be refunded, if any) BroadVox -- http://www.broadvox.net/ -- decided to terminate our contract without any valid reason, and the only explanation they could cite was "it's because of the software

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

First of all, I'm not knocking Sipura/Linksys. I have heard very good things about their products. I'm just wondering if they are the only quality shop on the market. I know about the zoom 5801 where you can't dial out the FXO from SIP, only from the FXS port. And I have heard similar about the HT-488 also. I want to know if anyone else makes ATAs where all of the features work

Hello everyone. Let me first begin by explaining what I'm trying to do... I have a calling card that has an access number and requires a PIN to be entered and then the number you want to dial, like normal calling cards. So what I have done is assign a local DID which when called, initiates a Dial to the access number of the calling card. Now, I'm having a hard time figuring out how to

This is a wierd one. Can't figure it out. I have an SPA-3000 at the house handling my incoming line. It's setup to direct the incoming call to asterisk. Works great 99% of the time. A few times a day, I'm getting calls that ring once internally and are then hungup. I managed to get a detailed log [1] of what's happening today and it looks to me that the SPA is acting wierd.

Hi, I've searched almost everywhere but have not come across a solution so I was hoping one of your fine folks can help me out. The problem is that a carrier is passing me early media on calls that sometimes have problems connecting. For example, calls to India mobile might play an early media message saying "the phone is out of reach" if mobile is out of area of coverage. Problem

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

Hello all, I have an ISDN termination box (TR1) that converts ISDN(Bri) to 2 normal analogue lines. The same number is assigned to these lines. These lines are connected to 2 spa3k registered to my asterisk box. When calls arrive, TR1 try to pass call to the first spa. If spa not takes the call immediately then try to pass to the other spa. The only configuration I found works is to put the

OK, I've spent way more time than I wanted to on getting an x100p clone to work in Australia. I'm happy to consider other (more functional) options. Does anyone have an opinion on both the Sipura 3000 and other Digium cards (like the TDM400P)? I need something that works with no much fuzz. I know the Sipura 3000 is cheaper the the TDM400P card. All I need is to channel my POTS line

Hi, Anybody here from the UK using Asterisk at home? I'm looking for a SIP phone which will work with Asterisk and not leave me broke! I got one of the Tecom ones from Solwise but it refuses to login to Asterisk server for some reason. May have to send it back. What are the other options please? Thanks Mike

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible